Q1. Choose the correct answer for the following: (Answer 5 only).1. When the stopband of a BSF is 5 kHz and the cut-off frequency of the HPF in the parallelcircuit is 20 kHz, the cut-off of the LPF is approximately:a) 15 kHzb)20 kHzc) 30 kHzd) 35 kHz2. If the carrier frequency received by AM receiver is 1.2 MHz, the local oscillator should bethe following frequencies:set on one ofa) 1.2 MHzb) 455 kHze) 2.4 MHzd) 1.655 MHz3. Image frequencies in AM superheterodyne receivers are removed by:a) Low pass filterb) Band pass filtersc) The IF staged) The mixer4. If the frequency of the input signal is 500 kHz, and the transistor in class C amplifierconducts for 5% of the cycle time, the conduction time isa) 2 usb) 0.2 µsc) 5 usd) 0.5 us5. A carrier signal of 0.5 MHz is AM modulated by another signal of 10 kHz, the outputs of thebalanced modulator are the following frequencies:a) 410 kHz, 510 kHzb) 490 kHz, 510 kHz, 500 kHzc) 490 kHz, 510 kHz.d) 0.5 MHz, 0.51 MHz, 0.48 MHz6. In class C amplifier, if the power supply is 12 V and the tank circuit has a resistance of 80 (2,the maximum output power isa) 1.44 Wb) 1.44 mWc) 900 mWd) 288 mW

1. Given stop band frequency of BSF is 5kHz, High pass cut off frequency is 20kHz. Cut off…

Q1. Choose the correct answer for the following: (Answer 5 only). 1. When the stopband of a BSF is 5 KHz and the cut-off frequency of the HPF in the parallel circuit is 20 kHz, the cut-off of the LPF is approximately: a) 15 kHz b) 20 kHz c) 30 kHz d) 35 kHz 2. If the carrier frequency received by AM receiver is 1.2 MHz, the local oscillator should be set on one of the following frequencies: a) 1.2 MHz b) 455 kHz c) 2.4 MHz d) 1.655 MHz 3. Image frequencies in AM superheterodyne receivers are removed by: a) Low pass filter b) Band pass filters

Q1. Choose the correct answer for the following: (Answer 5 only). 1. When the stopband of a BSF is 5 KHz and the cut-off frequency of the HPF in the parallel circuit is 20 kHz, the cut-off of the LPF is approximately: a) 15 kHz b) 20 kHz c) 30 kHz d) 35 kHz 2. If the carrier frequency received by AM receiver is 1.2 MHz, the local oscillator should be set on one of the following frequencies: a) 1.2 MHz b) 455 kHz c) 2.4 MHz d) 1.655 MHz 3. Image frequencies in AM superheterodyne receivers are removed by: a) Low pass filter b) Band pass filters

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A tuned circuits of the oscillator in an AM transmitter used a 50 micro Henry coil and a 1 nano Farad capacitor. Its oscillator output is being modulated by a 176Vp audio frequencies up to 10KHz. Solve for the upper and lower sideband frequency and bandwidth occupied by the sidebands. If the depth of modulation is 80 percent, solve for the total transmitted power delivered to the antenna having a 24 ohm resistance
1) Calculate the bandwidth and baud rate for an FSK signal with mark frequency 34 kHz, space frequency 26 kHz, and input bit rate 2 kbps. Use the calculator for bandwidth. 1.1) Using a table of Bessel functions, determine the minimum bandwidth for the FSK signal. Remember that the significant bands are taken for those with amplitude > 1%. As the table is normalized (Jo=1 at most), the significant sidebands are those with amplitude > 0.01)
(vsb modulation) 1-Interpret graphs of time domains and explain the relationships between them. 2-Interpret graphs of frequency domains and explain the relationships between them.
In a DSB-AM communication system, the carrier signal is given as c(t) = 8 cos(8tt) and the message signal m(t) = sinc(2t). What is the spsB-AM (t) bandwidth of the modulated signal? noteHiçbiri =None
1.Select the correct statement(s) regarding the FM Index. a. Δf represents the amount of frequency that the carrier wave can change in order to represent the baseband (information/message) signal b. β=(KvcoAm)/fm is a ratio that has no units c. the larger the FM index, the greater the frequency bandwidth d. all statements are correct 2. Select the correct statement(s) regarding viewing an information signal in time and/or frequency domains. a. only the viewing a signal in the time domain is important since the transmission/carrier frequency is an assigned parameter b. observing the signal in the time domain does not give you information regarding the capacity or bandwidth of the signal c. a signal observed in the frequency domain provides information regarding signal amplitude and the periodic or non-periodic nature of the signal d. all of the above are correct 3. Select the…
a. An AM transmitter has the unmodulated carrier power of 20kW and can be modulated to a maximum of 70% before the system saturates/overloads. Find the value to which carrier power can be increased if 40% modulation limit is imposed.b. An analog communication system using FM has the highest modulating frequency of 5 kHz and maximum deviation of 25 kHz. Calculate the bandwidth of modulated signal using Carson’s rule. Compare this value with the one obtained using the simple formula. For practical systems which of these values should be used?
A receiving antenna picks up 50 micro volts of signal. The transmitting antenna switches to a nearby antenna which has a 5 dB gain over the original antenna. How much of the new signal is picked up by the receiving station? Show the calculation in detail.
solve only question 1.b 1.a) Calculate the bandwidth and baud rate for an FSK signal with mark frequency 34 kHz, space frequency 26 kHz, and input bit rate 2 kbps. Use the calculator for bandwidth. 1.b Using a table of Bessel functions, determine the minimum bandwidth for the FSK signal from the previous problem (Problem 1.a). Remember that the significant bands are taken for those with amplitude > 1%. Since the table is normalized (Jo=1 at most), the significant sidebands are those with amplitude > 0.01). -- Indications: In your answer, place the result without the units and expressed in kilohertz
1- Indicate the sidebands in the modulated signal spectrum. 2- Calculate Signal-to-noise (SNR) at the input. 3- Select suitable channel model and explain the choice of your selection. NOTE: The Carrier frequency used in the FM communication system is 43.67 MHz. The other parameters are given in image
For an FM modulator with a modulation index m=1.5, a modulating signal v_m (t)=V_m sin⁡(2000πt), and unmodulated carrier v_c (t)=12 sin⁡(12000π×10^3 t), determine: a) Number of sets of significant side frequenciesb) Their amplitudesc) Draw the frequency spectrum showing their relative amplitudesShow the complete solution thank you
A signal is to be transmitted into the line where the link has a bandwidth of 50000kHz at the same time the signal is to be sampled, quantized and binary coded to obtain a pulse code modulation (PCM) signal. The signal is sampled at the Nyqiust rate. Assuming that 2 bits can be transmitted per second over a 1 Hz bandwidth determine the minimum transmission bandwidth BT that can be used to successfully transmit this signal.
If the bandwidth of the signal m(t) is B, which is the most bandwidth-efficient? Which oneis the least bandwidth-efficient? Briefly explain WHY? (a) Single sideband suppressed carrier (SSB-SC)(b) Vestigial sideband amplitude modulation (VSB)(c) Phase Modulation (PM)(d) Double sideband suppressed carrier (DSB-SC)