i need the answer quickly Q1. Choose the right option for the following. Conviny1. If a DC voltage is applied to a DC motor, then, according to Fleming's Left hand Rule, the motorthat develops a torque which causes the rotation.will experience.a. Back EMF (Eb)b. Mechanical forcec. Energyd. None of the above2. The lost torque resulting from the difference (Ta - Tsh) represents_a. iron lossc. friction loss3. Ta/la characteristic in series motor is aa. straight lined. if the answer is not existed above, then draw the C/CSb. curve (parabola)4. Generator is said to be commutatively-compounded when_a. series field aids the shunt fieldc. the commutation device is useda. it reduce the core resistancec. it reduce the core weightb. electrical lossd. both a and cc. curve (exponential)b. series field opposes the shunt fieldd. none of the above5. Thin laminations eliminate the eddy current losses in the armature core, sinceb. it increase the core resistanced. it make the core as a short circuit

Since you have asked multiple questions in a single request, we will be answering only the first…

Q1. Choose the right option for the following. [. viny 1. If a DC voltage is applied to a DC motor, then, according to Fleming's Left hand Rule, the moto that develops a torque which causes the rotation. will experience. a. Back EMF (Eb) b. Mechanical force c. Energy d. None of the above 2. The lost torque resulting from the difference (Ta - Tsh) represents_ a. iron loss c. friction loss 3. Ta/la characteristic in series motor is a a. straight line d. if the answer is not existed above, then draw the C/CS Conorator is said to be commutatively-compounded when b. curve (parabola) b. electrical loss d. both a and c c. curve (exponential)

Q1. Choose the right option for the following. [. viny 1. If a DC voltage is applied to a DC motor, then, according to Fleming's Left hand Rule, the moto that develops a torque which causes the rotation. will experience. a. Back EMF (Eb) b. Mechanical force c. Energy d. None of the above 2. The lost torque resulting from the difference (Ta - Tsh) represents_ a. iron loss c. friction loss 3. Ta/la characteristic in series motor is a a. straight line d. if the answer is not existed above, then draw the C/CS Conorator is said to be commutatively-compounded when b. curve (parabola) b. electrical loss d. both a and c c. curve (exponential)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Need ASAP. Will upvote!a dc machine runs no load with a speed of 200 rad/s. The applied armature voltage is Va = 120 V. At a load of 5Nm the speed drops by 10 rad/s.a) what is the voltage for a no load speed of 150 rad/s? B) What is the current for a torque load of 5Nm? c) What voltage is needed to run the machine at 200 rad/s with a torque of 5Nm?
A 220V shunt generator has an armature resistance of 0.02ohms and a shunt field resistance of 44ohms. at rate load, the driving engine develops 62.26hp. If the iron and friction losses amount to 1600W, how much is the current delivered to the load at this condition? (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses and Efficiency on the DC MACHINE) (I need a clean solution ma'am/sir. Thank you do much)
Pls explain the following. 1. What is Torque in DC motor and its types
Derive the following in terms of the physical parameters of the induction machine: a- the slip at maximum torqueb- the maximum torque
Q3 A 200v series motor takes a total current of 40A and runs at 900 rpm. If the armature and field resistances are 0.20 and 0.10 respectively. Iron and friction loss are 0.4 Kw, find the output power of the motor, efficiency and the torque developed in the armature
The flux o in a 16 KW, 100 V, Duplex Lap-Wound DC machine has been set to induce rated voltage at a speed of 1500 RPM. Find the product Ko, and find the induced torque in this machine at rated load. Select one: O a. Product = 0.0667 , and Induced Torque = 10.667 N.m O b. None O c. Not enough information is given to find the torque O d. Product = 0.6366 , and Induced Torque = 101.86 N.m
what is the best suitable motor for below application? In a belt conveyor system used to transport bulk solids, the belt speed is required to be maintained constant at the set speed all the time irrespective of the bulk solids content on the belt. Hence, the electric motor used in this system should be able to operate more or less at a constant speed in a wide range of different torque values.
The field and armature resistances of a 220-V series dc motorare 0.2 ohms and 0.1 ohms respectively. The motor takes 30 A ofcurrent while running at 700 rpm. If the total iron and frictionlosses are 350 W, find the efficiency.
Q1) A 4-pole, separately excited, wave wound DC machine with 0.12 armature resistance is rated for 230 V and 5 kW at a speed of 1200 rpm. If the same armature coils are reconnected to forms a lap winding, what is the power (in kW) at 1200 rpm of the reconnected machine if the field circuit is left unchanged? Also calculate the voltage regulation in both cases
The field and armature resistance of a 400V shunt motor are 200 ohms and 0.1ohm, respectively. The motor takes 30A of current while running at 1000 rpm. If the frictional losses are 400W, determine the motor efficiency.
A d.c. shunt machine has armature and field resistances of 0.025 Ω and 80 Ω respectively. When connected to constant 400-V bus-bars and driven as a generator at 450 r.p.m., it delivers 120 kW. Calculate its speed when running as a motor and absorbing 120 kW from the same bus-bars
A 460V, 25 hp, 60 Hz, 4 pole, Y-connected wound rotor(R2) has the following impidances in Ω/phase refered to the stator circuit. R1= 0.64 Ω , X1= 1.106Ω , R2=0.332Ω ,X2=0.464Ω , Xm=26.3 a)Torque max? b) Slip max? c) Wm at which Torque max occurs?? d) Starting Torque? e) If R2 is doubled what is the speed at which the max torque occurs now? f) Plot the original torque-speed curves and the adjusted T (with R2^2)