Q1. Figure Ql shows a translational mechanical system. (i) Obtain the freebody diagram for the 6 kg mass. (ii) State the number of degrees of freedom of the system. (iii) Determine the equations of motion for the system. X(s) (iv) Derive the transfer function, G(s)= F(s)' x(t) 3 N-s/m 5 N/m 6 kg At) Figure Q1

Q1. Figure Ql shows a translational mechanical system. (i) Obtain the freebody diagram for the 6 kg mass. (ii) State the number of degrees of freedom of the system. (iii) Determine the equations of motion for the system. X(s) (iv) Derive the transfer function, G(s)= F(s)' x(t) 3 N-s/m 5 N/m 6 kg At) Figure Q1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An extremely fast photodiode can be designed to achieve bandwidth of 158 GHz. Assuming that the bandwidth is limited by carrier transit time, calculate the required depletion region if the electron and hole saturation velocities = 0.85 x10^5ms-1. Express your answer in the unit of μm.
a) Complete the incomplete root locus below.b) For which value range of K is the system stable?
A) The effective aperture of a 144.0cm-diameter parabolic reflector antenna is 6m of the physical aperture area. Compute the gain in dB at 10GHz. b) Vodafone decides to use a digital TDMA scheme that can tolerate a Signal-to-Interference Ratio of 17dB in the worst case. Find the optimal value of the path lost exponent for an omnidirectional antenna; assuming i=3 and j=2. Assume that there are six co-channel cells in the first tier, and all of them are at same distance from the mobile. Use suitable approximations. c) Draw the table of frequency assignments and system layouts for a seven-cell repeat pattern and three-sectored antenna per cell site, using E-GSM 900MHz in which the total number of channels needs to be divided, assuming that the full spectrum is available from the operator of the system is used. In the sixth (6th) cluster, list all the possible channels that will be assigned to the cells in sector B?
At t=0, a 1 pound force, denoted by f(t), is applied to the translational mechanical system. Determine K and M such that the response has a 1 second peak time and 4 second settling time if fv = 1. Additionally, what is the resulting overshoot percentage? Determine also the resulting transfer function as well as the steady state error for step input.
A communication system has a bandwidth of 150 MHz and an SNR (dB) of 35 dB. a. What is the theoretical maximum data rate (C) on this channel?b. How many signal levels (symbols) do we need to achieve this data rate?c. If we want to increase the maximum data rate to 10 Gbps, what SNR (dB) do we need on this medium?
i) A communication system employs a continuous source. The channel noise is white and Gaussian. The bandwidth of the source output is 10 MHz and signal to noise power ratio at the receiver is 100. (a) Determine the channel capacity. (b) If the signal to noise ratio drops to 10, how much bandwidth is needed to achieve the same channel capacity as in (a). (c) If the bandwidth is decreased to 1 MHz, what S/N ratio is required to maintain the same channel capacity as in (a).
You have an FSK transmitter using a mark frequency of 500 kHz, a space frequency of 380 kHz, and sending 10 kbps. A) How much bandwidth do you need for your transmission? B) if you are to design the system with continuous phase shift keying in mind, what would be the value of the space frequency if the mark frequency remains the same?
A network operator has asked you to design a point-to-point optical link for short reach (2 km) transmission inside a data centre. The operator’s primary concerns are; (i) to minimise capital expenditure (i.e. to keep deployment costs as low as possible) and (ii) to have excellent receiver sensitivity. (a) Draw a block diagram of the optical link you propose, outlining the components used and the reasons for your design choices. (b) Regarding your transmitter design choice: How will electrical information be transferred to the optical domain in your system? And what are the potential drawbacks of this technique? Please use drawings in your answer.
Answer the following: (a) What is the maximum data rate for a 64-level system with an analog bandwidth of 400 MHz? (b) What is the maximum data rate if that same system is subject to noise, with an average power level of 600 and an average noise level of 200? Include units in your final answer.
Derive the
An optical fiber link with a distance of 30km long has a loss of 0.3dB/km. a) Calculate the minimum optical power level that must be launched into the fiber to maintain an optical power level of 3.0W at the receiving end.b) Estimate the required input power if the fiber has a loss of 0.6dB/km.c) Differentiate, with the aid of diagrams, the types of these dispersions and its effect on the transmission distance. (i) Modal Dispersion(ii) Chromatic Dispersion(iii) Polarization Mode Dispersion
Consider a stable LTI system with input x(n) and output y(n). The zero-pole pattern of y(n)consists of a double zero at the origin of the z-plane and the poles 3 ± 3j. The zero-pole pattern ofx(n) consists of a double zero at the origin of the z-plane. Find the system function and the systemimpulse response.