Q1. The rigid link is supported by a pin at A, a steel wire (E,) BC having an unstretched length of L2 and cross-sectional area of 22.5 mm? and a short aluminum block (Eal) having an unloaded length of L and cross-sectional area of 40.5 mm?. If the link is subjected to the vertical loads shown, determine the average normal stress in the wire and the block. L2 -150 mm- 100 mm 150 mm D L1

Q1. The rigid link is supported by a pin at A, a steel wire (E,) BC having an unstretched length of L2 and cross-sectional area of 22.5 mm? and a short aluminum block (Eal) having an unloaded length of L and cross-sectional area of 40.5 mm?. If the link is subjected to the vertical loads shown, determine the average normal stress in the wire and the block. L2 -150 mm- 100 mm 150 mm D L1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported rectangular concrete beam 6m long is reinforced with four-28mm diam tension bars and two-28mm diam. compression bars. The beam has a width of 300mm and overall depth of 400mm. The steel covering to the centroid of reinforcements is 70mm, fc’=30 MPa and fy=418 MPa. a. Draw the stress diagram b. Compute for the Ultimate moment capacity of the beam
The assembly consists of two posts AD and CF made of A-36 Steel (E= 200GPa) and having a cross-sectional area of 1000m^2 and a 2014-T6 aluminum (E=73.1GPa) post BE having a cross-sectional area of 1,500m^2. If a central load of 400KN is applied to the rigid cap, determine the normal stress in each post. There is a small gap of 0.10mm between the post BE and the rigid member ABC.
A square hollow steel strut with a wall thickness, t_{1} = 10 mm is pin connected to two gusset plates, having a thickness t_{2} = 12mm which are welded to the base plate having a thickness of 12 mm and fastened to a concrete base by 4-16 mm Ø anchor bolts. Diameter of pin is 16 mm. Compressive load P = 48kl , θ = 30°. Calculate the shear stress in the pin in MPa.
Point B of the system given below is movable support and Enpoint is fixed bearing. According to the given loading condition a) Draw the normal force, moment and shear force diagrams. B) Check whether the section used between AB-BC-CD is suitable, as the material has normal allowable stress em = 85 Mpa and shear strength em = 50 Mpa. c) Find the diameter d of the section used between DE-EF since the normal allowable stress of the material is em = 85 Mpa and the shear strength is em = 50 Mpa.
A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa GIVEN: b= 350 mm d= 600 mm L= 6 m Wd = 13 kN/m WL = 36 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
An overhang beam is loaded as shown below. The beam cross-section was butlt by attaching two (2) channels to a 9mm thick plate using 16mm rivets. The property of the channel is given below: Depth, D = 225 mm Flange Thickness, t= 9mm Flange Width, B, -112.5 mm Web Thickness, t. -9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t= 100 MPa on shear, for bearing, o,-200 MPa on single shear, a, =260MPa on double shear. 1. determine the location of centroid, ȳ, from top of the beam in mm 2. determine the moment of inertia, I, of the section in mm4 3. determine the maximum allowable moment, Mall, inkn-m, base on the beam's cross section.
The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminum rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I = 50 x 106 mm4 for the beam, Eal = 70 GPa, and A = 42 mm2 for the rod.
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Thickness, tf=9mm Flange Width, B=112.5 mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear 1. Determine the location of centroid, ȳ, from top of the beam in mm
A square hollow steel strut with a wall thickness, t_{1} = 10 mm is pin connected to two gusset plates, having a thickness t_{2} = 12mm which are welded to the base plate having a thickness of 12 mm and fastened to a concrete base by 4-16 mm Ø anchor bolts. Diameter of pin is 16 mm. Compressive load P = 48kl , θ= 30°. Calculate the bearing stress between the strut and the pin in MPa.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear Determine the location of centroid, y, from top of the beam in mm Determine the moment of inertia, I, of the section in mm^4. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. Determine the location of the maximum moment on the beam in meters. Determine the maximum moment, in kN-m, on the beam Determine the maximum flexural stress on the beam in MPa.
The rigid bar ABC is hinged at A and supported with a 6mm diameter steel wire at B. The bar is horizontal before the load W is applied at C. Assume the bar and the wire to be weightless. 1. If the allowable stress in the wire is 160MPa, the maximum load W (in kN) will not exceed 2. If the allowable downward movement at C is 9mm, the maximum load W (in kN) will not exceed 3. If the allowable stress in the wire is 180MPa and the weight of the bar is 80N/m, the maximum load W (in kN) is nearest to
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.