Answered: Q12) Two discrete-time signals; x [n]…

Q12) Two discrete-time signals; x [n] and y [n], are given as follows. Compute x [n] *y [n] by employing convolution sum. x [n] = 26[n]−8[n-1]+[n−3] y [n] = Ô [n+1] + 6 [n] +26 [n−1]- $ [n-2]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find y[n] if x[n]= [ u(n+2)-u(n-2)] and h[n]= 2+ n for n=-1, 0, 1, 2 please solve step by step Subject:signal and systems
please help answer these 2 only. thank youQ3 in a digital telephony network, the signal of human voice needs to be sampled and digitized before transmission. it is found that limiting the bandwidth of human voice to 3000 hz would be enough to ensure good-quality phone calls. a. Human voice contains frequency components above 3000 Hz. How canwe ensure that the voice signal will only occupy a bandwidth of 3000Hz? e. Now, suppose a frequency division multiplexing (FDM) system is to bebuilt to support 40 phone calls in a given geographic area, where asingle sideband amplitude modulation scheme (SSB AM) with asufficiently large carrier frequency is used for each phone call. What isthe minimum required bandwidth for the FDM system that can avoidmutual interference among the phone calls?
1.Find the impulse response of the equivalent system (i.e,, find h[n]) such that y[n]=x[n]∗y[n]holds where h1[n]=h[n]+0.5drag[n−1], h2[n]=0.5drag[n]−0.25drag[n−1], h3 [n]=(0.5)n u[n]with u[n]denoting unit-step function. this is a signal systems question
Determine the output of the systemdescribed by the following difference equations with inputand inital conditions as specified belowby using only time-domain operations. a)y[n]−0.5y[n−1]=2x[n],y[−1]=3, x[n]=(−0.5)n u[n]. this is a signal systems question
Show that the derivative of a 1-D signal, I=I(x), amplifies the higher frequency components of the signal. Then, prove that even a slight amount of noise n=n(x), can be responsible for a large difference between the derivative I and I+n (Hint: Assume that n can be written as εsin(ωx) for some very small ε and very large ω).
The transfer function is H(s) = (1.2s+0.18)/(s3 + 0.74s2 + 0.92s) and C(s) = (K(s+1))/ s A) A disturbance input W(s) =W/sk , where W is a constant, into the feedbackcontroller as shown below. We set R(s) = 0. What type of disturbance input W(s)(step, ramp, or parabola) can thesystem reject (i.e., the steady-state error ess is a nonzero constant)? (B) Suppose you want to design the controller C(s) to produce a closed-loop response to areference step input that has no more than 30% maximum overshoot (Mp ≤ 0.30) and a peak timeof no more than 8 sec (tp ≤ 8). Given the specifications on Mp and tp , compute the constraintson the damping ratio ζ and the damped natural frequency ω, assuming that the closed-loop systemis approximated as a 2nd-order underdamped system. Sketch the allowable regions in thecomplex plane (the s-plane) that these constraints define, and shade in the regions where the polesshould not be placed.
In a linear time-invariant discrete-time system, x[n] is the input and y[n] is the output. Unit at the entrance of the systemWhen initial conditions are zero when step (u[n]) is applied y[n] = 3(1/2)^n It is known that u[n] is output.Accordingly, create the transfer function of the system and find the unit sample answer for this system. (h[n]=?) Reminder: This question also covers z-transformation and inverse z-transformation.
The input output relation for a discrete time system is expressed by the following difference equation: y(n)=ax(n)+bx(n-1)+cx(n-2)+dy(n-1)+ey(n-2) where a,b,c,d,e are non zero coefficients. Find out the two intermediate transfer functions if the system is to be realised by direct form 1.
Q3 in a digital telephony network, the signal of human voice needs to be sampled and digitized before transmission. it is found that limiting the bandwidth of human voice to 3000 hz would be enough to ensure good-quality phone calls. a. Human voice contains frequency components above 3000 Hz. How canwe ensure that the voice signal will only occupy a bandwidth of 3000Hz? b. The sampling rate is determined to be 50% higher than the Nyquistsampling rate. Determine the sampling rate c. A pulse-code modulation (PCM) scheme is used to represent thedigitized voice signal, where 10 bits are used for each sample.Determine the data rate of a single voice call. d. Time-division multiplexing (TDM) is used to aggregate a maximum of 40voice calls in a telephone line. Determine the maximum data rate thatyou can observe over a telephone line. e. Determine the minimum required bandwidth of the telephone line thatcan support a maximum of 40 phone calls.- d. Explain what…
Could you answer the d and e parts and show the calculations clearly. Thanks a lot. Btw, this question is about the digital signal processing (electrical electronic engineering) Compute for this system, a) h[n], the impulse response b)Calculate y[n] for given x[n] analytically c) Calculate y[n] using graphical convolution d)Is this system causal? Why? e) What is this system used for?
Calculate the value of expression ∑2n=-2= h[n] for the impulse-response h(n) of a system defined by the constant coefficient difference equation in discrete-time y[n]-0,8.y[n-1]+0,15.y[n-2]=x[n]-0,3.x[n-1] and specify it as the response. thank you:)
a) h[n] = {-1,1,2,3}Above defines the impulse response h[n] of a certain LTI aystemDetermine the output signal,y[n] of the system considering that a signal x[n] = {-1,-2,t2,3} is applied to the system. b)