Q16 A 240V, 50 Hz, single-phase capacitor start a.c. motor is loaded such that the slip is 6% the motor constants referred to the stator are : Stator resistance 2.20; rotor resistance = 3.80 Stator reactance 30; rotor reactance 2.10 Magnetizing reactance 860 ; iron and friction loss 500 Draw the equivalent circuit and from it find the output power and efficiency at the given leading Anci 1000 w 7A CO

Q16 A 240V, 50 Hz, single-phase capacitor start a.c. motor is loaded such that the slip is 6% the motor constants referred to the stator are : Stator resistance 2.20; rotor resistance = 3.80 Stator reactance 30; rotor reactance 2.10 Magnetizing reactance 860 ; iron and friction loss 500 Draw the equivalent circuit and from it find the output power and efficiency at the given leading Anci 1000 w 7A CO

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-phase, 440-V, delta-connected, 4-pole 50-Hz induction motor runs at a speed of 1447 rpm when operating at its rated load. The equivalent circuit has the following per-phase :parametersr1=0.2 Ω, x1=x2'=2 Ω , r2'=0.4 Ω, rc=200 Ω , xɸ = 40 Ω Using the approximate circuit, determine, for rated load, the values of line current and power factor, torque, output power and efficiency. The mechanical loss is 1000 watts.
TOPIC: AC Machines - Induction Motor A three-phase, 3 KV, P=24, 50Hz, Y-connected slip ring IM has a rotor resistance of 0.015 ohm and a stand still reactance of 0.265 ohm per phase. Full load torque Is obtained al a speed of 245 rpm. Neglect stator impedance, Calculate (A) Ratio of Maximum Torque to Full load Torque (B) Speed at Maximum Torque
Three-phase induction motor, 460 V 50 Hz, 4 poles, 50 hp with Delta, operating at 3.8% slip rated torque when receives Line Voltage 460 V, 50 Hz The parameters of the equivalent circuit per phase are as follows.R1 = 0.33, X1 = X2 = 0.42 and Xm = 30 Ohm / phase.Answer the following questions by neglecting the mechanical losses, Core losses and Stray load losses.A) Value of the rotor resistance R2 B) Maximum torque and rated speed C) line current and starting torque of motor
3-phase, 50 Hz, 4-pole, 220 V, 10A ASM has an ASM 0.85 back power coefficient. stator copper losses are 500 W and rotor copper losses are 200 W. Friction and wind losses 100 W, core losses 300 W and stray load losses 50W. According to this; a. Air gap strength b. Mechanical strength produced c. Output power in horsepower D. Yield e. Slipping f. Working Speed g. Torque Produced h. Output Torque i. By specifying the asynchronous Motor power flow diagram from input to outputby drawing?
A 240 V, Short – Shunt DC Generator supplies a load current of 60 A. The armature circuit resistance is 0.10 Ohms and shunt-field circuit resistance is 120 Ohms. The series-field resistance is 0.08 Ohms. Calculate The developed Power The percentage voltage regulation. Draw the power flow graph, showing the various losses as well the input, developed, and output power values. P rotational = 500W
Q/ dc shunt generator 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * 2-The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * 3-Output of the prime motor…….kwatt * 4-Mechanical , electrical and overall efficiency …….. * 5-Flux per pole is......... wb *
A 25 HP, 6 pole, 50 Hz, 3-phase slip ring induction motor runs at 960revolutions per minute on full load with a rotor current per phase of 35 A.Allowing 250 W for the copper loss in the short-circuiting gear, and 1000Wfor mechanical losses, find the resistance per phase of the three-phaserotor winding.
A three phase, 220V, 50Hz, rpm mesh connected synchronous motor has a synchronous reactance of 4 ohms per phase, it recieves an input line current of 30A at a leading power factor of 0.8. find the line value of induced emf and the torque angle expressed in mechanical degree by use of phasor diagram
A 400V, 50Hz, 6-pole 3-phase asynchronous motor rotates 20Nm of constant load torque at 950rpm. If it is desired to rotate this load at 750 rpm mechanical speed;a) The synchronous speed of the motor,b) Supply frequency,c) Find the value of the supply voltage between phases?Note: The motor will be driven with V/F sbt because the load torque does not change.
A three-phase, 460-V, 60-Hz, four-pole Y-connected induction motor has the following equivalent circuit parameters: Rs = 0.42Ω, Rrʹ = 0.23Ω, Xs = Xrʹ = 0.82Ω, and Xm = 22Ω. The no-load loss 60W, may be assumed constant. The rotor speed is 1750 rpm. The rotational losses at this speed is 500W. Use the approximate equivalent circuit in figure below, to determine (a) the synchronous speed Ns; (b) the slip s; (c) the input current Ii; (d) the input power Pi; (e) the input PF of the supply, PFs; (f) the gap power Pg; (g) the rotor copper loss Pru; (h) the stator copper loss Psu; (i) the developed torque Td; (j) the efficiency; (k) the starting current Irs and starting torque Ts; (l) the slip for maximum torque sm; (m) the maximum developed torque in motoring, Tmm
A 20KW, 440V, short shunt compound dc generator has full load efficiency of 87%. If the resistance of the armature and interpoles is 0.4ohm and that of the series and shunt fields 0.25ohm and 240ohms respectively, calculate the combined bearing friction, windage and core loss of the machine A 10 kW 250 volts self-excited generator, when delivering rated load, has an armature-circuit voltage drop of 5% of the terminal voltage and a shunt field current equal to 5% of the rated load current. The resistance of the armature is 0.02 ohm. Calculate the voltage generated and power output.
Give answer as soon as possible A 200 V dc shunt motor runs at no-load speed of 1000 rpm and takes line current of2 A. When it runs at rated load, the speed of the motor reduces to 920 rpm. Ifsupply voltage is constant, then calculate the line current drawn by the motor atrated load and mechanical power developed by the motor (neglect magnetic andstray load losses).