Q2// A floor system consists ofconcrete slab supported by continuous with: hy = 140mm , b, = 300mm,d = 550mm, f 28MPa, fy = beam %3D %3D 420MPа. Determine the steel reinforcement required at mid span of interior beam to resist service dead load moment M = 320kN.m and service live load moment M, = 250 kN. m 8m Зт 3m 3m + 1-1

Q2// A floor system consists ofconcrete slab supported by continuous with: hy = 140mm , b, = 300mm,d = 550mm, f 28MPa, fy = beam %3D %3D 420MPа. Determine the steel reinforcement required at mid span of interior beam to resist service dead load moment M = 320kN.m and service live load moment M, = 250 kN. m 8m Зт 3m 3m + 1-1

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

A floor systtem consist of a 75 mm concrete slab supported by continuous T beams with a span of 4.3 m spaced at 3 m on center. The beams have a web width, bw and effective depth, d. Calculate the necessary reinforcement for a typical interior beam if the applied factored load is 574 kN-m. Solve the following given a. ) bw = 400 mm; d = 500 mm; fy = 420 MPa; fc' = 28 MPa b. ) bw = 350 mm; d = 470 mm; fy = 420 MPa; fc' = 21 MPa
A rectangular beam 250 mm wide, 500 mm deep is reinforced at thebottom with 4-20-mm-diameter bars and at the top with 2-16-mmbars. Concrete cover to bar centroid at the top is 80 mm and at thebottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yieldstrength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 3. Determine the design moment capacity of the beam in negativebending. = [n] kN∙m (whole number)
A rectangular reinforced concrete beam has a length of 7.5 m. It is supported with a hinged at one end and a roller 2m from the other end. The width of beam is 350 mm and the overall depth is 550 mm. The beam is reinforced with 5D25 tensionreinforcement and 2D25 compression reinforcement located at 60 mm from the outermostfiber of the beam. The concrete strength fc = 28 MPa and steel yield fy= 390 MPa. Determinethe following:a. Sketch the beam and its cross sectionb. Stress in the compression steel.c. Moment capacity of the beam.d. Factored uniform load throughout the entire span of the beam that could carry.
1. A rectangular reinforced concrete beam has a length of 7.5 – 10.5 m. It is supported with a hinged at one end and a roller 2m from the other end. The width of beam is 350 mm and the overall depth is 550 mm. The beam is reinforced with 5D25 tensionreinforcement and 2D25 compression reinforcement located at 60 mm from the outermostfiber of the beam. The concrete strength fc = 28 MPa and steel yield fy= 390 MPa. Determinethe following:a. Sketch the beam and its cross sectionb. Stress in the compression steel.c. Moment capacity of the beam.d. Factored uniform load throughout the entire span of the beam that could carry.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at thebottom with 4-20-mm-diameter bars and at the top with 2-16-mmbars. Concrete cover to bar centroid at the top is 80 mm and at thebottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yieldstrength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 2. Determine the design moment capacity of the beam in positivebending. = [m] kN∙m (whole number)
A rectangular beam 250 mm wide, 500 mm deep is reinforced at thebottom with 4-20-mm-diameter bars and at the top with 2-16-mmbars. Concrete cover to bar centroid at the top is 80 mm and at thebottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yieldstrength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the limiting tensile steel ratio for a tension controlledcondition in positive or negative bending with the given materialstrengths. ρt = [r] in 5 decimal places (ex. 0.00001)
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement area of 4072 sq. mm at the bottom. fc' = 25 MPa, fy = 414 MPa. c) Determine the value of "Mu"
A spiral column carries a service dead load of 1000 kN and a service live load of 900 kN. fc' = 27.5MPa and fy = 413.5 MPa. Using a steel ratio of 0.03 a. What is the diameter (mm) of the spiral column?b. How many pieces D28 longitudinal reinforcement is required?c. Determine the possible spacing (mm) of the 10 mm spirals assuming a 40 mm concrete cover.
5. Design a rectangular reinforced concrete beam to resist service moments of 195 kNm from dead loads and 145 kNm from live loads. The beam dimension are (b x d) 250 x 500 mm. Assume fck = 30 N/mm2 and fyk = 500 N/mm2. The depth to compresssion reinforcement is 45mm.Take until 2 decimal point for each calculation.
A rectangular bear has a wish of 300mm and a total depth of 650mm , calculate the area of steel reinforcement repral Take, M. 360kN.m f30 MPa and , 400MP
A T‐beam has the following properties:Flange width, bf = 820 mmFlange thickness, t = 100 mm Width of web, bw= 250 mmEffective depth, d = 470 mm concrete strength f’c = 20.7 MPa steel strength, fy = 414 MPaDetermine the required tension steel area for the following conditions:A) MDL = 150 kN.m, MLL = 120 kN.mB) MDL = 175 kN.m, MLL = 190 kN.m
Question 33 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only.