Q2: An exterior flat slab has a span of (6.0*5.2)m and is supported on a rectangular column atthe edges with (0.4m*0.4m)and an interior circular column with (0.4m) in diameter.The slabthickness is (180 mm) and without drop panel.With fe'= 28 MPa, f, -325 MPa and Y₁ = 24 kN/m³1) Check for shear.2) Calculate the required steel for the positive and negative moments in column strip inthe long direction.The imposed live load is 7.5 kN/m² and the surfacing load is 1.2 kN/m². Use $12mm forreinforcement.$0.40 m5.2m110.40.t.t.biyom6.0m

Slab : A slab is a structure which is supported by beams or walls which distributes the load of…

Q2: An exterior flat slab has a span of (6.0*5.2)m and is supported on a rectangular column at the edges with(0.4m*0.4m)and an interior circular column with (0.4m) in diameter.The slab thickness is (180 mm) and without drop panel.With fe'= 28 MPa, f, -325 MPa and Y= 24 kN/m 1) Check for shear. 2) Calculate the required steel for the positive and negative moments in column strip in the long direction. The imposed live load is 7.5 kN/m² and the surfacing load is 1.2 kN/m². Use $12mm for reinforcement. $0.40m 0 5.2m 10.40 m biyom 6.0m O O O

Q2: An exterior flat slab has a span of (6.05.2)m and is supported on a rectangular column at the edges with(0.4m0.4m)and an interior circular column with (0.4m) in diameter.The slab thickness is (180 mm) and without drop panel.With fe'= 28 MPa, f, -325 MPa and Y= 24 kN/m 1) Check for shear. 2) Calculate the required steel for the positive and negative moments in column strip in the long direction. The imposed live load is 7.5 kN/m² and the surfacing load is 1.2 kN/m². Use $12mm for reinforcement. $0.40m 0 5.2m 10.40 m biyom 6.0m O O O

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter17: Retaining Walls

Section: Chapter Questions

Problem 17.5P

See similar textbooks

Similar questions

A slab shown supports the load W1 and W2 for every one-meter strip along the longitudinal section. If the total length L= 15m and W=145 kN/m, determine the load W2 in kN/m so that the upward pressure on the slab is uniform and that the barge remains horizontal
e. Location of the total earth thrust from the base of wall (in meter) ya = f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at the base of wall is 25o and factor of safety against sliding is 1.5 (minimum). Consider 24 kN/m3 as the unit weight of concrete. B = Thankyou please
The one-way continuous slab is to support the moments. Consider f’c 21MPa and fy= 275 MPa; Dead load moment 42 kN.m/m at midspan- 67 kN.m/m at supports : Liveload moment 40 kN.m/m at midspan and 44 kN.m/m at supports : Windload moment + 133 kN.m/m at supports. Calculate: 1.What is the maximum positive factored moment? 2. What is the maximum negative factoredmoment? 3. What is the minimum depth permitted with no compressive reinforcement is assume and using 12 mm diameter rebars?
pls replyy asap!! Given the dimension of a gravity dam with top base = 2m, bottom base =6m, height = 8m and depth of water at the upstream side is 6m (acting on vertical side of the dam). Neglect hydrostatic uplift and use unit weight of concrete equal to 20 kN/m?. The coefficient of friction between the base of the dam and the foundation is 0.6. Determine the Factor of safety against sliding.
A trapezoidal concrete dam is 20m high. The upstream face is vertical and the water is flush with the top, which is 3m wide. The coefficient of friction between the base of the dam and the foundation is 0.60. It is required to have a factor of safety of 3m for overturning and Knowing that the specific gravity of ancrete is 2.40. a.) Find the required width of the base. b.) Find the factor of safety against sliding c) Find the pressure at the heel and toe
The section of the masonry dam is shown in Figure3a. If the uplift pressure varies uniformly from fullhydrostatic at the heel to full hydrostatic at the toe,but acts only over 2/3 of the area of the base, find(a) the location of the resultant; (b) the factor ofsafety against overturning; and (c) the factor ofsafety against sliding if the coefficient of frictionbetween base and foundation is 0.60. Unit weight of concrete and masonry is 23.54 kN/m3for all the problems NOTE: CLEAR HANDWRITTEN SOLUTION
A trapezoidal concrete dam is 27ft. high. The upstream face is vertical and thewater is flush with the top, which is 3ft. wide. The coefficient of frictionbetween the base of the dam and the foundation is 0.60. If it is required to havea factor of safety of 3 for overturning and knowing that concrete and waterweight 150 pcf and 62,4 pcf, respectively, find:a. The required width of the base;b. The pressures at the toe and at the heel of the dam.
The bin is 1.5 m wide and is filled with water to the level shown. Determine the resultant force on the side AB and on the bottom BC.
A trapezoidal concrete dam is 20m high. The upstream face is vertical with water is flushed with the top, which is 3m wide and the bottom width (base) is 14.52m. The coefficient of friction between the base of the dam and the foundation is 0.60. If the specific gravity of concrete dam is 2.40, find the factor of safety against sliding, The pressure intensity at the heel and toe in KPa
The appied load on a shallow square fondation makes an angle of 20° wiht the vertical. Given: B= 5 ft, Df= 3 ft, γ= 115 lb/ft3, φ’= 25°, and c’= 600 lb/ft2. Use FS= 3 and determine the gross inclined allowable load. Use Eq (6.28)
A trapezoidal dam has width at the top of 2m and width at the bottom is 14m. The upstream face is vertical and the total height of the dam is 22m. The depth of the water on the upstream face of the dam is 20m. If the coefficient of friction between the dam and the foundation is 0.88, using unit weight of concrete equal to 23.5 kN/cu.m, a) compute the factor of safety against slidingb) compute the factor of safety against overturning
A rectangular gravity dam has a height 5 m. It retains 3 m deep of water. Calculate the minimum width of the concrete dam that is necessary to prevent the dam from the sliding. The specific gravity of the concrete is 2.4 and the coefficient of friction between the base of the dam and the foundation is 0.50. Use factor of safety against sliding of 1.5.