Q2/ By using the power series method make a dimensional analysis forthe following variables; The frictional torque of a disc T- f(diskdiameter D. rotating speed N, viscosity of fluid u, and its density p).

Answered: Image /qna-images/answer/bf4c2838-00de-46b6-aac2-40d4dbdba141.jpg

Q2/ By using the power series method make a dimensional analysis for the following variables: The frietional torque of a disc T-f(disk diameter D, rotating speed N, viscosity of fluid and its density p).

Q2/ By using the power series method make a dimensional analysis for the following variables: The frietional torque of a disc T-f(disk diameter D, rotating speed N, viscosity of fluid and its density p).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.13P: 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its...

See similar textbooks

Related questions

Q: The development of a flow situation depends on the velocity V, the density, 3 linear dimensions (L1,…

A: Option D is the correct answer

Q: The lift of a wing, Fisft, is a function of wingspan, W, chord length, H, surrounding air density,…

A: Flift=fW,H,ρ,μ,V

Q: Applying Dimensional Analysis to the human anatomy studies, it was found that the velocity, c, at…

A: It is required to perform dimensional analysis for velocity

Q: Example: The pressure difference (Ap) between two point in a pipe due to turbulent flow depends on…

A: ∆P=fV, D, μ, ρ ,e, L

Q: Consider laminar flow over a flat plate. The boundary layer thickness & grows with distance x down…

Q: From Fourrier's law, the rate of heat transfer in pl. is described by: Q = S(k,A,AT, x) where k =…

A: Given Data⇒ Fourier's law of heat transfer : Q=fk,A,∆T,x We want to use Buckingham's Pi theorem to…

Q: Use the method of repeating variables to find out the non-dimensional groups for the problem of fan…

A: To find: The non dimension group . Given: The power is function of p=f(D,ρ,ω,Q). Here, P is power, D…

Q: 03: The power output (P) of a marine current turbine is assumed to be a function of velocity U,…

A: Solution: SInce number of variables is more than three, Buckingham π-theorem is more suitable for…

Q: The speed of sound c in an ideal gas is known to be a function of absolute temperature T, universal…

A: The complete derivation is attached as an image.

Q: Consider a propeller spinning in air. The thrust produced by the propeller is given by T. The…

A: The trust (T) is a function of the diameter of propeller (D), the kinetic viscosity (μ), the…

Q: Ex4: Verify the dimensions in both the FLT and MLT system of the following quantities;…

A: Write the equation to calculate acceleration which is the time rate of change of velocity. Now…

Q: Power generated by a propeller operating in the air (P); it depends on the mass density of the air…

Q: Task 2 Evaluate the use of dimensionless analysis using the Buckingham Pi Theorem for a given fluid…

Q: 1. Explain the three necessary conditions which must be met in order to achieve complete similarity…

A: The necessary condition which must be met in order to achieve similarity between a model and a…

Q: 1.5 The power generated by a pump PE is a function of the volumetric flow rate Q, the height of…

Q: Check the following equation for dimensional homogeneity: mv = [" (Fcost) at where m is mass, v is…

A: Given data: m v = ∫t1t2 F cos θ dt Where m is mass , v is velocity,F is force, θ is angle, and t…

Q: P5.37 The volume flow Q through an orifice plate is a function of pipe diameter D, pressure drop Ap…

Q: 03: The power output (P) of a marine current turbine is assumed to be a function of velocity U,…

A: In this question in the first part we have to prove the relation and in rest of the parts we need…

Q: How can I use dimensional analysis to show that in this problem both Froude's number and Reynold's…

Q: The drag force FD acting on a ship depends on the forward speed V , the fluid density ρ and…

A: Solution : Drag force , Fd=MLT-2speed , v = LT-1Density, ρ = ML-3viscosity,μ = ML-1T1gravity , g =…

Q: Q2/ By using the power series method make a dimensional analysis for he following variables: The…

Q: When a liquid in a beaker is stirred, whirlpool will form and there will be an elevation difference…

Q: The thrust force of propeller (P) depends upon the flow velocity V, angular velocity o, diameter D,…

A: Diamensional analysis Dimensional analysis is a method of simplifying a physical problem by dividing…

Q: The drag FD of the golf ball is affected by the speed V of the ball, the diameter d of the ball, the…

Q: Dimensional analysis can be used in problems other than fluid mechanics ones. The important…

A: T=fcnl,I,E,ρ,σ

Q: The Stokes number, St, used in particle-dynamics studies is a dimensionless combination of 5…

Q: 03: The power output (P) of a marine current turbine is assumed to be a function of velocity U,…

Q: 3. Andrade's equation is a proposed model of the effect of temperature on viscosity written as, H =…

Q: From Fourrier's law, the rate of heat transfer in plane surfaces is described by: Q = /(k, A, AT, x)…

A: The first step is to identify the dimensional variable, the non dimensional variable and the…

Q: Find the value of the following dimensionless group from the given data. a) The Froude number, NEr…

A: Solution:

Q: A- The power produced from a pump (P) is fun (Hon of flow (@), pressure drop (P), Density of fluid…

Q: During World War II, Sir Geoffrey Taylor, a British fluid dynamicist, used dimensional analysis to…

A: Dimension analysis is the method of establishing a relationship between different physical…

Q: The quantities viscosity µ, velocity V, and surface tension Y may be combined into a dimensionless…

Q: A U-tube mercury manometer is used to measure the pressure at a pointon the wing of a wind-tunnel…

Q: External Problem 2: Dimensional analysis and similarity The viscous torque T produced on a disc…

A: Given: A viscous torque produces on a disc rotating depend upon characteristics dimension D, the…

Q: Suppose we know little about the strength of materials butare told that the bending stress σ in a…

A: Since the bending stress proportional to half the thickness of the beam, we can state that…

Q: Under a laminar flow, the liquid flows through small holes. It has a triangular cross-section, width…

A: Given that ; Volumetric flow rate Q of the flow is a function of viscosity μ ,pressure reduction…

Q: The volume flow Q through an orifice plate is a function ofpipe diameter D , pressure drop D p…

A: Q is the function of (D, ∆P, ρ, μ, d) Where, Q is the volumetric flow rate D is the pipe diameter…

Q: The lift of a wing, Fit, is a function of wingspan, W, chord length, H, surrounding air density, p,…

Q: The spin rate of a tennis ball determines the aerodynamic forces acting on it. In turn, the spin…

A: Write the dimensional functional relationship. τ=fv, ρ, μ, D, ω, hf Write the basic dimensions of…

Q: The lift of a wing, Fift, is a function of wingspan, W, chord length, H, surrounding air density, p,…

A: Given: Lift of the wing is the function of the W, chord length H, air density ρ, viscosity μ and…

Q: The pressure drop, AP, in a horizontal pipe depends on the pipe diameter, d, pipe length, L, pipe…

Q: In making a dimensional analysis, what rules do you followfor choosing your scaling variables?

A: We have to explain the steps what we will follow for choosing spacing variables in dimensional…

Q: Q3: The power output (P) of a marine current turbine is assumed to be a function of velocity U,…

A: Data given- Power output P is a function of U,L,w,ρ,v

Q: When fluid in a pipe is accelerated linearly from rest, it begins as laminar flow and then undergoes…

Question

Q2/ By using the power series method make a dimensional analysis for
the following variables; The frictional torque of a disc T- f(disk
diameter D. rotating speed N, viscosity of fluid u, and its density p).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Suppose we know little about the strength of materials butare told that the bending stress σ in a beam is proportionalto the beam half-thickness y and also depends on thebending moment M and the beam area moment of inertiaI . We also learn that, for the particular case M = 2900in ∙ lbf, y = 1.5 in, and I = 0.4 in4 , the predicted stressis 75 MPa. Using this information and dimensional reasoningonly, find, to three significant figures, the onlypossible dimensionally homogeneous formula σ=y f ( M , I ).
The variables in a Saybolt viscometer are the time (t) required to empty a certain volume of oil of density (ρ) and viscosity (μ), a length (L) representing the dimensions of the viscometer, and the gravitational acceleration (g). Using the Buckingham Pi-theorem, show that
How can I use dimensional analysis to show that in this problem both Froude's number and Reynold's number are relevant dimensionless parameters? Problem: Here shallow waves move at speed c. The surface of the waves is a function depth (h), gravitational accelaration is g, densisty is p and fluid viscosity is μ. I need to get the parameter in the form in the image. Please help :)
Dimensional analysis is to be used to correlate data on bubble size with the properties of the liquid when gas bubbles are formed by a gas issuing from a small orifice below the liquid surface. Assume that the significant variables are bubble diameter D, orifice diameter d, liquid density rho, surface tension sigma (in N/m), liquid viscosity mu, and g. Select d, rho, and g as the core variables.
The variation of fluid pressure with height is described by the differential equation: dp/dz = - density *g Here, p is specific density and g is the local acceleration of gravity. For an ideal gas, p = M PIRT, where M is molar mass and R is the universal gas constant. Modeling the atmosphere as an isothermal column of ideal gas at 283.15 K (lO°C), estimate the ambient pressure in Denver, where z = l(mi1e) relative to sea level. For air, take M = 29 g molP1; values of R are given in App. A.
The force, F, acting on a billboard due to wind depends on it length, l, height, h, the modulus of elasticity of the board, E, and the specific weight, γa, of the air. Using dimensional analysis, find an appropriate dimensionless relationship.
Please answer this question using methods of repeating variables/ dimensional analysis. Thank you
The volume flow Q through an orifice plate is a function ofpipe diameter D , pressure drop D p across the orifice, fluiddensity ρ and viscosity μ , and orifice diameter d . Using D ,ρ , and ∆ p as r e peating variables, express this relationshipin dimensionless form.
The drag force FD acting on a ship depends on the forward speed V , the fluid density ρ and viscosity µ, gravity, its length L and width B and the average roughness height k. (a) Use dimensional analysis to express this information in terms of a functional dependence on nondimensional groups. (b) If the ship moved from fresh water to salt water, where the density and viscosity are both increased by 10%, how would its drag force change at fixed speed?
The thrust force of propeller (P) depends upon the flow velocity V, angular velocity o, diameter D, dynamic viscosity , density p. the speed of sound in the medium C. (1) Derive the relationship between the above variables and the thrust force by using Buckingham's IT-theorem. (2) Explain the physical meaning of the obtained dimensionless groups. إجابت
The speed of sound c in an ideal gas is known to be a function of absolute temperature T, universal ideal gas constant Ru, molar mass (molecular weight) M of the gas, and ratio of specific heats k. Showing all your work, use dimensional analysis to find the functional relationship between these parameters.
Acording to Darcy law, P is a pressure, V is a velocity, D is a diameter, g is acceleration gravity, f is dimensionless coefficient. Is the equation dimensionaly consistent?