Q2: Complete the sentences? 1- If the maximum friction force is 100 KN and normal force is 10 KN, the value of coefficient kinetic friction equal - 2- The value of coefficient statics friction is ---..if the kinetic friction is 0.7, 3- The value of friction angle is --------, if coefficient statics friction is 0.20. 4- Plate thickness is 5 mm. The rivet diameter in French formula is ------.

Q2: Complete the sentences? 1- If the maximum friction force is 100 KN and normal force is 10 KN, the value of coefficient kinetic friction equal - 2- The value of coefficient statics friction is ---..if the kinetic friction is 0.7, 3- The value of friction angle is --------, if coefficient statics friction is 0.20. 4- Plate thickness is 5 mm. The rivet diameter in French formula is ------.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
A 30 KN of force at one end just supports a weight of 30,000 KN load at the other end. If the rope is run three times around a circular post, what is the coefficient of friction between the rope and the post? How to get the final answer 0.366?
In the given figure, W= 200kg. Assume that the coefficient of friction between surfaces is 0.40. Which of the following most nearly gives the required force P to raise the block?
A 30 KN of force at one end just supports a weight of 30,000 KN load at the other end. If the rope is run three times around a circular post, what is the coefficient of friction between the rope and the post?
The maximum static friction for a material in contact with a rough surface 2 is 10kN. Determine the minimum force that would make an impending motion to the material.
2 A ladder 5 m long and weighing 260 N is placed against a vertical wall at an inclination of 30 ^ 0 with wall. A wan weighing 780 N climbs the ladder. When he is at a distance of 1.64 m along the ladder from lower all contact surfaces? end, the ladder slips. What is the coefficient of friction assuming it to be same for
What weight (kg) can be lifted by a double threaded screw that has an efficiency of 85% if it is opetated by a 52 lb force at the end of a 25 inches lever ?The pitch of the screw is 0.55 inches
A dictionary is pulled to the right at constant velocity by a 10 N force acting 30° upward above the horizontal. The coefficient of kinetic friction between the book and the horizontal surface is 0.5. What is the weight of the book?
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
A ladder of length 5 m is resting against a smooth wall, its point of contact being just below a first floor window. The bottom of the ladder rests on the ground and the coefficient of friction between the ladder and the ground is 0.3. A person of mass 75 kg climbs the ladder, which has a mass of 4 kg. The bottom of the ladder is at the point of slipping, outward from the wall, just as the person reaches the mid-point of the ladder’s length. Draw a free body diagram of the ladder and calculate the maximum frictional force opposing the slipping motion. In addition, determine the angle of inclination (θ) of the ladder, when the person is at the mid-point and the ladder is on the verge of slipping.
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
The pitch of 48 mm mean diameter threaded screw of a screw jack is 12.0 mm. The coefficient of friction between the screw and the nut is 0.12. (a) Determine the torque required on the screw to raise a load of 27 kN, assuming the load to rotate with the screw. (b) Determine the ratio of the torque required to raise the load to the torque required to lower the load and also (c) the efficiency of the machine.