Q2 /Fill up the blanks in the following: 5- Cement is manufactured by burning a mixture of 6- C3S, which is normally present in the largest amounts, cooling below 7- At any stage of hydration, the 8- In the semi-dry process, water weighing about 5-... and at high temperatures in a kilm °C. ... represent that part of the gross volume percent occurs 2-4 hours after mixing.

Q2 /Fill up the blanks in the following: 5- Cement is manufactured by burning a mixture of 6- C3S, which is normally present in the largest amounts, cooling below 7- At any stage of hydration, the 8- In the semi-dry process, water weighing about 5-... and at high temperatures in a kilm °C. ... represent that part of the gross volume percent occurs 2-4 hours after mixing.

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.25P

See similar textbooks

Similar questions

A tank initially holds 100 gallons of salt solution in which 50 tbe of salt has been dissolved. A pipe fills the tank with brine at the rate of 3 rpm. containing 2 lbs of dissolved sale per rallon. Auming that the mixture is kept uniform by stirring drain pipe draws out of the tank the mixture at 2 pm. Find the amount of mult in the tank at the end of 30 minutes.
A plastic media biotower has vertical flow packing with n = 0.5 and k20 of 0.045min-1. The tower is cylindrical with a diameter of 10 m. Depth of packing medium is 6 m.Primary effluent flow rate is 2500 m3/day with a soluble BOD5 of 250 mg/L. The average wastewater temperature is 16 oC. Direct recirculation is practiced at 1:1 ratio. Calculate the following: a. Organic loading rate of the biotowerb. Hydraulic loading rate of the biotowerc. Recirculation ratiod. Effluent soluble BOD5 concentration
A plastic media biotower has vertical flow packing with n = 0.5 andk20 of 0.045 min–1. The tower is cylindrical with a diameter of 10 m.Depth of packing medium is 6 m. Primary effluent flow rate is 2500m3/d with a soluble BOD5 of 250 mg/L. The average wastewatertemperature is 16°C. Direct recirculation is practiced at 1:1 ratio.Calculate the following:a. Organic loading rate of the biotowerb. Hydraulic loading rate of the biotowerc. Recirculation ratiod. Effluent soluble BOD5 concentration
MPN of effluent is 106/100 ml and it reduces to 102/100 ml after chlorination. Find percentage removal (%R) and log removal (logR) of MPN.
Evalaution sof aggregates Sources.
A large rank contains 100 gal of brine in which 10 lb of salt is dissolved. Brine containing 0.2 lb of salt to the gallon runs into the tank at the rate of 6 gal/min. The mixture, kept uniform by stirring, runs out of the tank at the rate of 4 gal/min. Find the amount of salt in solution in the tank at the end of t minute. Pls show complete solution
-4 2.LacticacidhasaKa of1.38x10 . What is the pH of the solution that results when 25.0 mL of 0.300 M lactic acid are titrated with 20.0 mL of 0.375 M KOH?
A sample of wet aggregate 297.2 N. After drying in an oven, this sample weighed 281.5. The absorption of this aggregates is 2.5%. Calculate the percent of free water in the original wet sample. Weight of the wet aggregates (Wwet) = 297.2 N Weight of the dry aggregates (Wdry) = 281.5 N
Complete the following problems dealing with rapid mix tanks and flocculation basins:1. Design a rapid mix tank for water at 50° F flowing at Q = 4.0 MGD for a typical process train ina drinking water treatment plant. Use a square tank with a depth 1.25 times the width, a designvelocity gradient G = 900 sec−1, and a hydraulic detention time τ = 30 seconds. Specificallydetermine:a. Rapid mix tank dimensions in feet and inches, to the nearest one inch.b. Input water horsepower (hp).c. Impeller rotational speed if a vane-disc impeller is used having a diameter half of the tankwidth and employing six flat blades and a baffled tank.2. Design a flocculation basin for water at 10°C flowing at Q = 49,200 m3/day for a typical processtrain in a drinking water treatment plant. The basin shall be a cross-flow, horizontal-shaft, paddlewheel type with an average velocity gradient of G = 26.7 sec−1, a detention time τ = 45 minutes,and a Gτ value of 50,000 to 100,000. Tapered flocculation shall be…
y'=(3x^2+4x-4)/(2y-4), y(1)=3 (Neat and clean solution!)
A 1,200 gpm WTP is being designed for treating iron and manganese. The influent manganese concentration is 80 mg/L and the iron concentration is 90 mg/L. How much oxygen (mg/L DO) from aeration is needed for design? Assuming that aeration only removes 85% of Fe and Mn, how much potassium permanganate is needed (mg/L)? Design standards require 30 days of chemicals onsite. Assuming that the chemicals onside are dry, how many lbs of potassium permanganate are required? If the treatment plant is to operate two filter cells at a time, what is the required SA of each cell, assuming SOR of 2.5 gpm/sqft?
3. Circular clarifiers are used to remove solid materials from water. They allow continuous treatment of water and can handle fairly large flows. Solids settle to the bottom of the clarifier and are carried away by a small stream of water (the waste stream). Most of the water exits the tank as treated effluent. Assume a clarifier receives a flow of 0.10 m3/s with a solid concentration of 800 mg/L. If the waste stream consists of 3% of the incoming flow and carries 90% of the incoming solids, a) what is the solids concentration in the waste stream, and b) what is the solids concentration in the treated effluent?