Q2: For the beam shown in Figure (2), determine transverse shear stresses at points E, Fand G on the cross section. The load P=100 KN and Ina = 470016mm". 12 mm *|| D B 1 0.2m .0.4m 0.2m 6 nea 4mm 96mm 48mm :12mm

Q2: For the beam shown in Figure (2), determine transverse shear stresses at points E, Fand G on the cross section. The load P=100 KN and Ina = 470016mm". 12 mm *|| D B 1 0.2m .0.4m 0.2m 6 nea 4mm 96mm 48mm :12mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given: Maximum positive shear = 3960 N Maximum negative shear = 5640 N Maximum positive moment = 20700 N-m Maximum negative moment = 2400 N-m Location of maximum shear from the left end of beam = 19 m Location of maximum moment from the left end of beam = 14 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Exercise caution in choosing the value of "c". (Be it known obviously that for beams with irregular cross-sections, Ctop ≠ Cbottom) Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
Given: Maximum positive shear = 3960 N Maximum negative shear = 5640 N Maximum positive moment = 20700 N-m Maximum negative moment = 2400 N-m Location of maximum shear from the left end of beam = 19 m Location of maximum moment from the left end of beam = 14 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
Given: Maximum positive shear = 387.50 kN Maximum negative shear = 602.50 kN Maximum positive moment = 1970.65 kN-m Maximum negative moment = 1480 kN-m Location of maximum shear from the left end of beam = 22 m Location of maximum moment from the left end of beam = 15.23 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. The entire shaft is made of steel for which G = 77 GPa. 1. Calculate the torque in segment CD in N.m. 2. Calculate the torsional shear stress on the surface of segment BC in MPa. 3. Calculate the angle of twist of segment AB in degrees. 4. Calculate the angle of twist of point A relative to point D in degrees.
Given: Maximum positive shear = 387.50 kN Maximum negative shear = 602.50 kN Maximum positive moment = 1970.65 kN-m Maximum negative moment = 1480 kN-m Location of maximum shear from the left end of beam = 22 m Location of maximum moment from the left end of beam = 15.23 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Exercise caution in choosing the value of "c". (Be it known obviously that for beams with irregular cross-sections, Ctop ≠ Cbottom) Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
The beam AC is simply supported at A and C and subject to the uniformly distributed load of 300 N/m plus the couple of magnitude 2700 N ⋅ m as shown in figure. Write the moment equation between A and C. Draw the shear and moment diagram. Determine the maximum shear and flexural stress of the beam with a rectangular cross section of 150mm x 250mm.
Q9c. For the beam below, the point loads and distances are as follows: F1 = 11. 25 kN, F2 = 11.25 kN and F3 = 4.50 kN L1 = 2.25 m, L2 = 4.50 m, L3 = 4.50 m and L4 = 2.25 m Determine the bending moment at D. Give your answer in kilonewton metres (kNm) to two decimal places.
The internal shear force V at a certain section of a steel beam is 80 kN, and the moment of inertia is 64,867,500 mm4. Determine the horizontal shear stress at point H, which is located L = 17 mm below the centroid. 58.9 MPa 42.7 MPa 39.6 MPa 35.2 MPa 31.2 MPa
Since the beam M in the figure is under the effect of simple bending moment, calculate the bending stress and shear stress values at the A, B and C points. h = 400mm b = 140mm and M = 150KNm