Q2: In a direct FM generation, it was used Hartly VCO. Given the capacitance constant as K.If you have the message signal m(t) = 3.4 sin(2n200t) V and required carrier frequency is fe =97.5MHZ, with frequency deviation of 12KHz. Calculate the required capacitor value for this VCO system.120n/F.%3D%3D

Given m(t) = 3.4 sin(2x200t) V Carrier Frequency is fc = 97.5mhz, K = 120n/F ∆f =…

Q2: In a direct FM generation, it was used Hartly VCO. Given the capacitance constant as Ke = If you have the message signal m(t) = 3.4 sin(27200t) V and required carrier frequency is fe = 97.5MHZ, with frequency deviation of 12KHz. Calculate the required capacitor value for this VCO system. 120n/F.

Q2: In a direct FM generation, it was used Hartly VCO. Given the capacitance constant as Ke = If you have the message signal m(t) = 3.4 sin(27200t) V and required carrier frequency is fe = 97.5MHZ, with frequency deviation of 12KHz. Calculate the required capacitor value for this VCO system. 120n/F.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

13) This MCQ QUESTION FROM ANTENNA ENGINEERING course.
The equation of an angle-modulated voltage is v = 10 sin (l08t + 3 sin 104,). What form of angle modulation is this? Calculate the carrier and modulating frequencies, the modulation index and deviation, and the power dissipated in a 100-ohm resistor.
1. What are Microwaves? Bring out the basic advantage of Microwaves over Co-axial cables andthe Fiber optics.2. Describe the basic Microwave transmission system and give the importance of each componentin the system.3. With a neat diagram show the reflections occurring in a transmission line. Hence explain theconcepts of Reflection co-efficient and VSWR associated with it.
A rectangular guide with dimensions of 5.7cmX2.524cm has air as its dielectric and operates at a frequency of 4.21GHz. Get The first 4 cut-off frequencies of the TE modes and the first of the TM modes (in GHz),phase constant in TE10 mode guide (in rad / m),phase velocity in TE10 mode guide (in Mm / s),
Multiple Choice directions: Circle the letter of the answers 7. This is a special microwave coaxial cable used in the lower microwave bands L, S, and C. a. Flexible coaxial b. All of the above c. Hard line cable d. Braided coaxial 8. The practical microwave region is in the vicinity of a. 1-10 GHz b. 1-20 GHz c. 1-300 GHz d. 1-30 GHz 9. In a hybrid ring, if the signal is applied at port 1, which port has no output? a. 3 b. 2 c. 1 d. 4 Note: Explanation is not needed just provide the correct answers for each number.
Which row represent the most stable system and why? nyquist and root locus plot attached.
Suppose Rc=10 k, Rb=1k, Vcc=4V, Vi =5V, and β= 200. Find Vbe, Vce, Ic, and the region of operation.
A cellular radio transmitter has a power output of 3 W at 800 MHz. It uses an antenna with a gain of 3 dBi. The receiver is 5 km away, with antenna gain of 12 dBi. Ignoring feedline losses and mismatch, calculate (a) the EIRP in dBW (b) the free space path loss, (c) the power delivered to the receiver in W and dBm
Design a rectangular microstrip patch antenna, based on the dominant mode, that can be mounted on the roof of a car to be used for satellite cellular telephone. The designed center frequency is 1.6 GHz, the dielectric constant of the substrate is 10.2 (i.e., RT/duroid), and the thickness of the substrate is 0.127 cm. Determine the (a) dimensions of the rectangular patch (in cm) (b) resonant input impedance, assuming no coupling between the two radiating slots (c) mutual conductance between the two radiating slots of the patch (d) resonant input impedance, taking into account coupling (e) position of the feed to match the patch antenna to a 75-ohm line
A ground-mounted photovoltaic module array for a commercial building may be constructed so that it can be used as? A. a storage area B. a covered walkway C. covered vehicle parking D. a break area for building occupants
Consider a mobile system at 900 MHz carrier frequency, and with 25-kHz bandwidth, that is affected by thermal noise (noise temp Te = 300k). Antenna gains of Tx and Rx sides are 8dB and -2dB respectively. Cable loss at Tx is 2dB. The noise figure at Rx is 7dB. The required operating SNR is 18dB and desired range of coverage is 2km. The break point is at 10dB up to which the path loss is given by [ ] , beyond that point the path loss exponent is 3.8, and the fading margin is 10dB. What is the minimum Tx power required?
A linear array is to be designed that operates at 10 GHz and has a 1◦ beamwidth (assume uniform illumination). This array must electronically scan to 65 ◦ without grating lobes. What is will the element spacing be? How many elements will be used?