Q2: The pin-connected structure shown in figure below consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E= 105 GPa] with a cross-sectional area of A1= 290 mm?. Bar (2) is an aluminum alloy [E= 70 GPa] with a cross-sectional area of A2= 650 mm?. If a load of P= 30 kN is applied at B, determine: II (a) the normal stresses in both bars (1) and.(2) (b) the downward deflection of point B on the rigid bar. |(1) 2250 mm 670 mm 480 mm 650 mm A 1600 mm P = 30 kN (2)

Q2: The pin-connected structure shown in figure below consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E= 105 GPa] with a cross-sectional area of A1= 290 mm?. Bar (2) is an aluminum alloy [E= 70 GPa] with a cross-sectional area of A2= 650 mm?. If a load of P= 30 kN is applied at B, determine: II (a) the normal stresses in both bars (1) and.(2) (b) the downward deflection of point B on the rigid bar. |(1) 2250 mm 670 mm 480 mm 650 mm A 1600 mm P = 30 kN (2)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid bar ABC is pinned at A and supported by the cables at point B as shown in the figure. The rod is pin connected. Diameter of bar is 36 mm θ. A load P equal to 100 kN is applied at C. E = 200,000 MPa. Coefficient of thermal expansion is 12x10 -6/C degrees. How to solve the displacement of C if the temperature rises by 60 degrees? Also, how to compute the tensile stress induced by the 100kN in rod BD. Compute the load P that a cable at C with a diameter of 16 mm θ can carry so that it will noy exceed a displacement of B equal to 2 mm. Neglect the thermal stress
Example 2: Rigid rod supported by BDE, AB and CD. AB is made of aluminum (E = 70 GPa) and its area is 500 mm2, CD is made of steel (E = 200 GPa) and its area is 600mm2. Find a) the displacement at B b) the displacement at D c) the displacement at E due to the 30kN force acting at the end of E. Solution: We find the forces from the free body diagram of BDE.
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze. Answer in 1 decimal place
2.) Given the truss shown, determine the value of the horizontal reaction at B. C= 14 KN D=20 KN E = 54 KN F = 61 KN g= 7 m The answer must be in KN.
A vertical steel bar ABC is pin-supported at its upper end and loaded by a force P1 at its lower end. A horizontal beam BDE is pinned to the vertical bar at joint B and supported at point D. Load P2 and moment M are applied at end E. Calculate the vertical displacement δC at point C if the loads are P1 = 2.5 kip, P2 = 1 kip, and M = 25 kip-in. The modulus of elasticity is E = 29,000 ksi and crosssectional areas are A1 = 0.25 in2 A2 =0.15in2 .Ignore the weight of the bar.
The crane BC shown below lifts a load of W. Neglecting the weight of the crane. Determine the following: a.) The Tension at Point A in terms of W. b.) The Reaction at Point B in terms of W.
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.
The outer diameter of the solid steel pipe shown in the figure is 25 mm. If the pipe is fixed at point E as in the figure and is subjected to a force of 800 N, a torque of 45 N.m and a moment of 300 N.m I applied from the other end of the pipe as in the figure, it will form at point A; (a) Principal planes (Ɵ1, Ɵ2). (b) Prime requirements (σmax,σmin), (c) their principal planes,
A uniform load of 8 kN/m acts on segment BC of the rigid beam shown. The beam is supported by a steelrod BD having a cross sectional area of 200 mm2. Determine the vertical displacement of the beam at Cafter the distributed load is applied. For steel, E = 200 GPa. Neglect the weight of the beam. Express youranswer in mm.
The given figure, (a) what is the reaction at C in kN? (b) what is the force at member AD and BD in kN?
The solid steel rod (1) shown in the figure has an allowable shear stress of 3 ksi. The brass tube (2) has an allowable shear stress of 8 ksi. The outside diameter of the tube is D2 = 1.63 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B.Calculate(a) the largest torque T that can be applied at the upper end of the steel rod if the allowable shear stress in tube (2) is not to be exceeded.(b) the corresponding minimum diameter d1 required for steel rod (1).
determine the support reactions at point A,B & C. TAKE NOTE: The support C is fixed and Support B is an internal hinge. Kindly show your complete solutions.refer to the given figure below.