Q2 : The three bars shown in fig are pined at point B which carry a load P and fixed at points A, C and D. The length of the three bars AB, BD and CB is (L) . The cross section area for each bar is A, except the bar CB which has different cross section area of A. All three bars have the same young modulus E. Determine the axial force in each of the bars.

Q2 : The three bars shown in fig are pined at point B which carry a load P and fixed at points A, C and D. The length of the three bars AB, BD and CB is (L) . The cross section area for each bar is A, except the bar CB which has different cross section area of A. All three bars have the same young modulus E. Determine the axial force in each of the bars.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 4 In the structure shown below, each of the rods BD and CE is made of brass (E = 105 GPa) and has a cross- sectional area of 200 mm?. Determine the deflection of end A of the rigid member ABC caused by the 2-kN load. (Hint: 1) consider equilibrium using the free body diagram of the rigid member ABC, 2) consider compatibility between the deflections of points B and C, 3) consider force-deformation relation of rods BD and CE) DO E 2 kN 225 mm В F 550 mm 75 mm 100 mm
F ., É, are applied to the truss system. В a) Find member forces in each member and state if the members are in tension or 4 m compression. b) If the maximum force that any member can support is Tmax in tension and Cmax in compression, determine the maximum value of P that can be supported. A E 3 т 3 m 3 т 3 m F1 F2 F3 F4 F5 Tmax Cmax P 2P 40° 7 kN 8 kN 2P Note: Do not show zero forces in your calculations.
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 633 mm2. For the 36 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 619 mm?. For the 41 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places 04 m 0.3 m E 0.4 m 0.2 m
Two members AB and AC are made of material with E= 91 Gpa and each member has cross sectional area of A= 290 mm2. The members are used to support bar BC. If P-2079 N, L1= 202 mm , L2= 313 mm and L3= 480 mm. Answer the following questions. L3 E В to L1 L2 The tension in member AB%3D he tension in member The elongation in member AB=
A cantilever beam (member AC) is supported with a column (member CD). Force P is applied to Point B, which is located at the midspan of the beam AC. The column is required to prevent excessive deflection of the beam as shown below. Determine the ratio of internal force in the column (member CD) to the critical buckling load of the column (Pcr). The length for both of the members, L, is 1,650 mm. The applied force, P, is 240 kN. The flexural rigidity for the beam and the column, EI, is 4.0X107 kN·mm2.
A For the beam loaded as shown in figure, the location of point of contra flexure from the left end is L Wo B
The force r is the resultant of the forces actingon the plate,find p1 and p2, if r=40kn and p3=20kn
The bars AB, AC, and AD are pinned together as shown in the Horizontal movement of the pin at A is prevented by the rigid horizontal strut AE. Calculate the axial force in the strut caused by the 10-kip load. For each steel bar, A = 0.3 in.2 and E = 29 x 106 psi. For the aluminum bar, A = 0.6 in.2 and E = 10 x 106 psi.
Q1-For the truss shown in figure, assume any value for the length (b) and explain how to find the forces in each member
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross sectional area of 500 mm^2. Link CD made of steel (E = 200 GPa) and has a cross sectional area of 600 mm^2. Determine the deflection at D in mm
2) 60 mm The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm. T = 1600 N - m 36 mm determine the angle of twist at A. T = S00 N- m 250 mm 375 mm A 400 mm