Q2/ Three resistors are connected together to form a current divider circuit as shown below. If the circuit is fed from a 100 volts 1.5kW power supply, calculate the individual branch currents using the current division rule and the equivalent circuit resistance. Ir e ‘ Trz V.= 0ov % 15kW - R 25Q ‘Im Ry 1000 Q2/Three resistors are connected together to form a current divider circuit as shown below.If the circuit is fed from a 100 volts 1.5kW power supply, calculate the individual branchcurrents using the current division rule and the equivalent circuit resistance.ITIRITR2IR3Vs =100V1.5kWR110ΩR2250R31002

ELECTRICAL NETWORK: When addressing a circuit problem or constructing a balanced circuit, the word…

Q2/ Three resistors are connected together to form a current divider circuit as shown below. If the circuit is fed from a 100 volts 1.5kW power supply, calculate the individual branch currents using the current division rule and the equivalent circuit resistance. IRI IR2 TRS V = 100V R1 R2 R3 1.5kW 102 250 1002

Q2/ Three resistors are connected together to form a current divider circuit as shown below. If the circuit is fed from a 100 volts 1.5kW power supply, calculate the individual branch currents using the current division rule and the equivalent circuit resistance. IRI IR2 TRS V = 100V R1 R2 R3 1.5kW 102 250 1002

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter2: Electrical Quantities And Ohm’s Law

Section: Chapter Questions

Problem 1PA: You are an electrician on the job. The electrical blueprint shows that eight 500-W lamps are to be...

See similar textbooks

Similar questions

Q1- True or FALSE A- the source voltage must be equal to the sum of individual voltages across individual resistors in a voltage divider circuit configuration True or False? B- in series parallel combinational circuit, the same current will always be in parallel resistors: True or False?
a. Calculate the voltages across each resistor in the circuit shown and record all results in Table below under the Calculated row. Note that Vsource is 5 V. b. Compute for the sum -Vsource+V330+V1k around loop 1, V470+V2.2k-V1k around loop 2, and -Vsource+V330+V470+V2.2k around loop 3 and record the result under the Calculated row.
Question 4 For the voltage-divider circuit shown: Part (A) Calculate the no-load voltage vo. Part (B) Calculate the power dissipated in R1 and R2. Part (C) If only 1 W resistors are available and that the no-load voltage is to be the same as inPart (A), specify the smallest values of R1 and R2.
Caution: This is a multiple choice question. You can mark more than one stylishIn the circuit in the figure, Vs = 6V, Is = 4A, R1 = 2 ohms, R2 = 2 ohms, R3 = 2 ohms. Calculate the voltage and resistance of Thevnin equivalent circuit visible from the ends of the R3 resistor.
1. A 12-ohm resistor is connected in parallel with a series combination of 8-ohmand 16-ohm resistors. If the voltage across the 8-ohm resistor is 48-volts,calculate the (a) total resistance, (b) total supply voltage, and (c) circuit current.2. A 45-ohm resistor is connected in series with a resistor R whose ohmic value isunknown. If the total current (taken by both resistors) is 7-amperes and thesupply voltage is 120-volts. Calculate the resistance R of the unknown.
Determine Voltage v₁ through V3 in the circuit of Figure 2 using source transformation and nodal Analysis.
Calculate the short circuit current is the 5 ohm resistor is the load resistance. Show complete solution.
A 10-ohms and a 20-ohms resistors are connected in parallel. Another resistor of 5-ohms is connected in series with the two. If the supply voltage is 48 volts, what is the current through 10-ohm resistors? Use Current Division Theorem
Measure the current and voltage values for all the components in the circuit using Voltage Divider Rule .And calculate elements powers and energies. The value of resistors as following: R1= 10KΩ, R2= 1000 Ω, R3= 50 Ω.
Complete Solutions 1. A 12-ohm resistor is connected in parallel with a series combination of 8-ohmand 16-ohm resistors. If the voltage across the 8-ohm resistor is 48-volts,calculate the (a) total resistance, (b) total supply voltage, and (c) circuit current.2. A 45-ohm resistor is connected in series with a resistor R whose ohmic value isunknown. If the total current (taken by both resistors) is 7-amperes and thesupply voltage is 120-volts. Calculate the resistance R of the unknown.
How do you calculate the voltages V2 and V4 using the voltage divider rule and using the following R values for the attached circuit?R1 = 660 MOhms R2 = 940 MOhms R3 = 1.1 GOhms R4 = 500 MOhms
In the circuit of figure 3.23, vs1=Vs2=0, is1=6A, Is2=12A. Represent the simplified circuit and calculate iBA and Vac. In the casesa) R=0 ohmb)R=6 ohmc)R=9 ohmd) R=10000 ohms