Q2. Determine the bearing reactions at A and B for the system shown in the figure if the speed is 300 rev/min (ccw). Determine the magnitude and the angular orientation of the balancing mas sif it is loaacated at a radius of 70 mm. y a 800 200- m1 R1 15° Тв A R2 m2 R3 m2 75° m3 m3 Figure 2. Rotating Shaft R1=30 mm, R2=50 mm, R3=55 mm, ml=2 kg, m2=1 kg, m3=3 kg.

Q2. Determine the bearing reactions at A and B for the system shown in the figure if the speed is 300 rev/min (ccw). Determine the magnitude and the angular orientation of the balancing mas sif it is loaacated at a radius of 70 mm. y a 800 200- m1 R1 15° Тв A R2 m2 R3 m2 75° m3 m3 Figure 2. Rotating Shaft R1=30 mm, R2=50 mm, R3=55 mm, ml=2 kg, m2=1 kg, m3=3 kg.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.60P: The force P applied to the brake handle enables the band brake to reduce the angular speed of a...

See similar textbooks

Similar questions

At the top A of the vehicle moving along line AC in the figureIts speed is 30 m / sec and its weight is 9 kN.Tool radius of curvature 40The reaction force to the tires when reaching point B, which is m,and so that the tires do not separate from the asphalt when it reaches point CWhat should be the radius of curvature of point C? (hA = 6 m andhC = 9 m)
find the angle of braking for a circular track of radius 600m as to be suitable for driving a car with a maximum speed of 180 km/hr (g=9.8m/s
Assuming there is no slippage for the belt assembly below, Determine the following: What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time? R1 = 0.3 m R2 = 0.2 m R3 = 0.1 m
Prove the relation that Hammer blow = ± mb x r*x ω2 where mb = Balancing mass placed at a radius of r* and ω= angular speed of the crank.
Calculate the amount of mass to be placed on the LCP and RCP with a radial radius of 0.2m in order to dynamically balance the shaft given on the right.m 1=3 kgm 2= 4 kgR 1=0.1mR 2=0.2m
A torque T = 0.30 N-m is applied to a bevel gear B. Bevel gear D meshes with gear B and drives pump A. Gear B has a radius of gyration of 150 mm and a weight of 50 N, whereas gear D and the im- peller of pump A have a combined radius of gy- ration of 50 mm and a weight of 100 N. Find how many revolutions of gear B are needed to get the pump up to 200 rpm from rest. What is the power output of the pump at this speed if it is 90% efficient.
The G weight of the figure, when descending, rotates the axis fixed to drums, which are supported by two cylindrical bearings of known dimensions, with known angular velocity ω. Determine the value of weight G, neglecting the rigidity and friction in the rope and assuming that the velocity diagram in the lubricant is linear. Given Data: μ = 8x10⁻² N/m², Di = 0.100 m,D = 0.02 m, Li = 0.1 m,De = 0.101 m, ω = 20/π rd/s
An inexperienced driver of a front drive car applies too much throttle in an attempt to accelerate from rest up the slippery 10 percent incline. The result is a wheel spin of the tires, each of which have the same gripping ability. Determine the vehicle acceleration for the conditions where the tire on the surface have ux = 0.01.
A motorcycle and rider have a combined mass of 350kg. The each wheel has a mass of 20kg with the diameter of 500 mm. The rider accelerates from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. Identify the magnitude and effect of gyroscopic reaction torque by calculating the angular velocity and power as the motorcycle ascends the incline when the motorcycle and rider travel at 80 km/h around a left-hand bend of road with the radius 30 m.Explain the effects of energy transfer in mechanical systems (e.g. gears, pulley or flywheel) with uniform acceleration present.
The spool has a weight of 40 lblb and a radius of gyration kOkOk_O = 0.4 ftft . A cord is wrapped around its inner hub and the end subjected to a horizontal force PPP = 8 lblb . Assume the spool rolls without slipping. (Figure 1) Determine the spool's angular velocity, measured clockwise, in 5 ss starting from rest.
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
At time t = 0, the operator of the road roller disengages the transmission so that the vehicle rolls down the incline as shown in the figure. Determine an expression for the vehicle’s speed as a function of time. The two rear wheels weigh 300 lb each and have a radius of 5 ft. The front wheel weighs 950 lb and has a radius of 3 ft. The vehicle body weighs 600 lb. Assume the wheels roll without slipping. The expression for the speed of the road roller as a function of time is given by v· = agsin(θ)v· = agsinθ .The value of a is determined to be: