can you please answer quickly Q2. In the adjacent figure we have R2 = 7.9 k2, R3 = 1.45 k2, and81 = 25 V, 82 = 10 V.R1a) If the ammeter shows the value +6 mA and the voltmetershows the value +5.8 V, determine the value of the resistor R1.b) Determine the electric current Iş.R:Ic) Determine the electric current I; by two different methods.d) Evaluate Kad along two different paths.e)|What would be the value of the voltage shown by thevoltmeter if we connected its red wire to the positive pole of thepower supply (electric current source) 8z and its black wire tothe negative pole of the power supply &,?Answer:

Answered: Image /qna-images/answer/be9af13f-aa68-4e3c-a65e-be195c7ac8fc.jpg

Q2. In the adjacent figure we have R2 = 7.9 kN, R3 = 1.45 k2, and E = 25 V, 82 = 10 v. R1 a) If the ammeter shows the value +6 mA and the voltmeter shows the value +5.8 V, determine the value of the resistor R1. b) Determine the electric current I3. c) Determine the electric current I2 by two different methods. d Fvaluate V.along two difforent nathe

Q2. In the adjacent figure we have R2 = 7.9 kN, R3 = 1.45 k2, and E = 25 V, 82 = 10 v. R1 a) If the ammeter shows the value +6 mA and the voltmeter shows the value +5.8 V, determine the value of the resistor R1. b) Determine the electric current I3. c) Determine the electric current I2 by two different methods. d Fvaluate V.along two difforent nathe

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given:Vb = 100 voltsR = 10000 ohmsC = 200 μFAssuming that after a long period of time, the switch is flipped from position "A" to position "B" at t=0. Determine the current in the source-free circuit after 1 second.
Using Passive Sign Convention, plot P2v(t) the power for the 2V source acrossthe following time range -10s ≤ t ≤ 10slabel athe plot
For the circuit shown in Figure P2.43, finda. The equivalent resistance seen by the source.b. The current i.c. The power delivered by the source.d. The voltages v1, v2.e. The minimum power rating required for R1.
Figure P1.27 shows an ammeter (AM) and voltmeter (VM) connected to measure thecurrent and voltage, respectively, for circuit element A. When current actually enters the + terminalof the ammeter, the reading is positive, and when current leaves the + terminalreading is negative. If the actual voltage polarity is positive at the + terminal of the VM, thereading is positive; otherwise, it is negative. (Actually, for the connection shown, the ammeterreads the sum of the current in element A and the very small current taken by the voltmeter. Forpurposes of this problem, assume that the current taken by the voltmeter is negligible.) Find thepower for element A and state whether energy is being delivered to element A or taken from it if a. the ammeter reading is +2 A and the voltmeter reading is +30 V.b. the ammeter reading is -2 A and the voltmeter reading is - 30 V.c. the ammeter reading is -2 A and the voltmeter reading is + 30 V.
Using Kirchoff's voltage law to determine the unknown voltage E2 for the configuration given in the figure below. Given that: - The source E1= 110 VV, - V1= 23.5 V, V2= 18 V, V3= 16.4 V, and V4= 20.5 V
In a design task, a wire of 2000 m requires to exhibit a voltage drop of 2.5 Vwhen 3.2 A of current passes though it. Based on the Table Q1 (b) below, inyour opinion, which of the wire is the most suitable for aviation when the fuelsaving is another factor to be considered as well.
The resistance of a certain aluminum power line is 150 Ω at 200 Find the line resistance when the sun heats up the line to 420C. First, use the inferred zero resistance temperature formula and then the temperature coefficient of resistance formula to show that the two formulas are equivalent.
the current (in mA) in each resistor shown in the figure aboveIR1IR2IR3 the potential difference between points c and f (Give the magnitude of your answer in volts and select the point of highest potential.) magnitude of potential difference What If? If all of the resistors in the circuit were decreased in value by a factor of 1,000, would the current in each resistor simply increase by a factor of 1,000? Explain your answer.
following equation applies: V = IR. Outside of the linear range, V*IR, outside of the linear ranges where resistors are broken The resistor has a resistance of 100ohm, and a power rating of 250mW. 1) Sketch the plot (and label) of the i-v relationship for the resistor using only the linear range of the resistor. Determine the range of values for the voltage and current that the resistor operates as a linear element and note these simplified numerical values on the plot.
a)Write the nodal equations and determine the potential values(voltages) of V1,V2 and V3 with respect to the ground b) Determine the current flowing through the resistor R2 c) Calculate the power at the resistor R3 and state either power is absorbed or dissipated
7. A conducting wire has a cross-sectional area of 2 mm² and a specific resistance of 5x10 m. designed for a heater with a power of 1200 Watt, operating at different potential 220 V. Determine a. Required wire length (L.) b. Large current on the wire c. Electrical energy is transferred into thermal energy within 15 minutes d. What is the power of the stove if the length of the wire is half the length in problem a (1/2)
A carbon resistor has a length of 25 mm and a uniform cross-sectional area equal to 0.3 mm^2. The conductivity of carbon at room temperature is 3 × 10^4 (A/m^2)(V/m). In a circuit the potential at one end of the resistor is V1 = 1.6V relative to ground and at the other end it is V2 = 1.8V. (a) Calculate the resistance of the resistor. (b) Calculate the conventional current in the resistor. (c) If the carbon resistor is replaced by one one-third the length and twice the cross-sectional area, how much would the conventional current in the new resistor now be worth if the same potential difference is maintained across its resistors? ends?