Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).

Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7P: Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer...

See similar textbooks

Similar questions

Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
An ideal transformer has no real or reactive power loss. (a) True (b) False
A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
A 1000-VA 380 / 110 V conventional transformer is to be used to supply power from a 490-V source to a110-V load. Consider the transformer to be ideal, and assume that all insulation can handle 490 V. (a) Sketch the transformer connection that will do the required job (b) Find the kVA rating of the transformer in the configuration. (c) Find the maximum primary and secondary currents under these conditions
As given in the figure, an ideal transformer with a 2: 1 winding ratio is fed from a 240 Volt source with an internal impedance of 8 + j6 Ω and transfers maximum power to the load impedance connected at its secondary. So, which of the following is the V2 voltage in the secondary?
A transformer outside of a business steps the average voltage down from V1 to V2. The transformer delivers an amount of power, P2, to the business at an efficiency of e. Which equation below will provide the amount of current provided to the primary coil?