Q3) Determine the depth and width at average and minimum flow and dimensions the weir plate of constant velocity grit chamber if Qmax = 4000 m³/day, Qavg =1500 m³/day, Qmin-500 m³/day, Grit diameter = 0.2 mm, S.G = 2.65, B=0.06. f= 0.03, control effluent width 0.25 m. What is the minimum length of chamber? =

Q3) Determine the depth and width at average and minimum flow and dimensions the weir plate of constant velocity grit chamber if Qmax = 4000 m³/day, Qavg =1500 m³/day, Qmin-500 m³/day, Grit diameter = 0.2 mm, S.G = 2.65, B=0.06. f= 0.03, control effluent width 0.25 m. What is the minimum length of chamber? =

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.7CTP

See similar textbooks

Similar questions

The peak and average flowrates for a velocity controlled grit chamber are 1.321 and 0.44 m3/s, respectively. Detention time is 1 min. and maximum velocity through the channel is 0.34 m/s. If channel width is 1.83 m, calculate the water depth in the channel, and design proportional weir the procedure given in bar rack design. The weir crest is 15 cm above the channel floor.
A bar rack channel is planned for the maximum flowrate of 2.0 m^3/s. When the flow velocity in the grit channel is maintained at a constant of 0.30 m/s, design a proportional weir for the effluent control. The width of the grit channel is 3.0 m. (C_d = 0.6)
This question in open channel hydraulic by chow/chapter 5
CORRECT LETTER PLS 1. Which of the following least affects hydraulic gradient or slope of HGL? A. PIPE LENGTHB. PIPE DIAMETERC. TYPE OF PIPED. FLOE RATE 2. In laminar flow, which is correct?BJ: higher Re value has higher friction factorJB: lower Re value has lower friction factorGroup of answer choices A. BJ is false and JB is true B. BJ is false and JB is false C. BJ is true and JB is false D. BJ is true and JB is true 3. In a system with 4 reservoirs and 2 pipe junctions, how many continuity equations are formulate? A. 3B. 2C. 1D. 4E. 5
The figure shows a weir, the base of which is 6m below the ground. The necessary flow net has also been drawn assuming Kx = Kv = K. K = 0.005 m⁄sec. Compute the following: rate of seepage through the foundation in liters/sec. uplift pressure at“f”. uplift force per unit length measured along the axis of the
A flow net for flow around a single row of sheet piles in a permeable soil layer is shown in Figure below with a scale as shown. Given that kx = kz=k = 4 x 10-3 cm/sec, determine How high (above the ground surface) the water will rise if piezometers are placed at points a and b The total rate of seepage through the permeable layer per unit length The approximate average hydraulic gradient at c factor of safety against piping x=1.6 y=2.8
A mechanically cleaned bar rack screen is installed ahead of a velocity controlled grit chamber. The bars are 10 mm thick, and the openings are 20 mm wide. The flow through the screen is 0.75 m3/s, and the depth of flow is 1.45 m in the channel upstream of the bar rack. 1. Calculate the flow velocity through racks (m/s). 2. Calculate the water depth in the channel downstream of the bar rack (m).
A 450 mm diameter culvert has been designed to convey a discharge of Q = 0.55 m3/s of storm-water under a residential road. The culvert is 37.5 m long and has a slope of 1.3%. The downstream flow depth was obtained as 0.35 m from a hydraulic analysis. You are required to determine:1.1 the head required to convey the discharge through the culvert at full flow conditions;(a) If concrete pipe is used with a Manning’s roughness coefficient of n = 0.0155 with an inlet headwall of socket type. (b) If corrugated steel pipe is used with a Manning’s roughness coefficient n=0.024 with an inlet headwall of square edge design. 1.2 What is the corresponding headwater depth in 1.1 (a) and (b) above?
A square concrete conduit having a side of 0.788 m carries water at a rate of 4 m3/s. Using Hazen-Williams formula with C=120, a.Compute for the hydraulic radius b.Compute the hydraulic slope. c.Compute the Head loss if the length of the conduit is 45m.
A flow net for flow around a single row of sheet piles in a permeable soil layer is shown in the Figure below. Given that kx= kz = k= 5.5 x 10-3 cm/sec, H1 = 6.5 m and H2 = 2.3 m determine: i. How high (above the ground surface) the water will rise if piezometers are placed at points a and b ii. The total rate of seepage through the permeable layer per unit length iii. The approximate average hydraulic gradient at c
A weir has difference of 7m in its water levels and there are 28 equipotential drops and 7 flow channels in its flownet. The soil's specific gravity is 2.7 and void ratio is 0.60. Determine the factor of safety against piping if the flow line is 1m long.
A deposit of cohesionless soil with a permeability of 0.3 mm/s has a depth of 12 m with impervious ledge below. A sheet pile wall is driven into this deposit to a depth of 8 m. The wall extendsabove the surface of the soil, and a 3 m depth of water acts on one side. Sketch the flow net and determine the seepage quantity. Provide a diagram a.600 ml/s/meter length b.300 ml/s/meter length c.900 ml/s/meter length d.1200 ml/s/meter length