I need to solve a question within 20minutes as quickly as possible Q3:In the transmission line shown, the impedance Zin (in ohms) between node Aand the ground isZ,= 502,1=0.5A%3D100n50 nZ, = ?Q3: A lossy transmission line has a complex propagation constant of y0.012+5.8 (/m). If the voltage is 12V at the generator port, what will bethe voltage magnitude when it propagates a distance of 12m?

Given, Line is of length l=0.5λZin1=Z0=ZL+jZ0tanβlZ0+jZltanβlfor λ2 line βl=2πλ×λ2=π

Answered: Q3: In the transmission line shown, the…

Q3: In the transmission line shown, the impedance Zin (in ohms) between node A and the ground is Z, = 50 2,1=0.5a 100 N 50 n Z, = ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.31P: A 500-kV, 300-km, 6()-Hz, three-phase overhead transmission line, assumed to be lossless, has a...

See similar textbooks

Related questions

Q: A transmission line operating at 125 MHz has Zo = 40 2, a = 0.02 (Np/m), and B = 0.75 rad/m. Find…

Q: 15.3 Determine the erection sag and tension of a transmission line at 65°C in still air. The line…

A: It is given that:

Q: A transmission line of 50 m long as shown in the figure below has Zo = 40 + j70 2, V. = 20 20 Vrms,…

Q: Q3) If the length of the transmission line is one-quarter wavelength (1 = 1 /4). Derive an…

A: We need to find out input impedance for quarter wavelength transmission line

Q: Fibre optic transmission line of unknown length L has an attenuation coefficient of 0.04 km1. When a…

Q: Q3: Design an L-section network to match transmission line of Zo = 50 Q with the load impedance of…

Q: 3-phase, 220kV, 200km overhead transmission line has its conductors on the corners of triangle with…

A: In this question we need to find a total inductance and capacitance of transmission line.

Q: An 33 kV, 3-phase transmission line has a length of 130 km is arranged as shown in the figure. Its…

Q: 1) A TV antenna lead-in wire 10cm long has a characteristic impedance of 250 Ω and is open-circuited…

A: As per company guidelines we are supposed to answer only one question. Kindly repost other questions…

Q: Q3: Design an L-section network to match transmission line of Z, = 50 2 with the load impedance of…

Q: Three-phase transmission line 90 km long Line impedance z=(0.4+j0.9) ohm/km, If the power Pr=60 MW…

Q: Q1: A. a lossless transmission line, with a length of 0.22, has an equivalent inductance 2500 time…

A: Given Parameters of a lossless transmission line.we need to find the characteristic impedance,load…

Q: Q5.For a transmission line with resistance, R, reactance X, and negligible capacitance, the…

A: Step 1 Resistance = R Reactance =X Capacitance is negligibleSince capacitance is negligible it is…

Q: The transmission line has the following data weight of the conductor = 3.3 kg/m, Tension in %3D the…

A: Weight of conductor, We =3.3 Kg/m Tension on conductor, T = 2589 Kg Sag, S = 4m Sag, S = (WL2) /8T L…

Q: A three-phase, 60-Hz, 69-kV transmission line has an inductance of 1.0531 mH/Km per phase and a…

A: In this question, We need to choose the correct options What is the transmission line parameter A?…

Q: A transmission line of 50 m long as shown in the figure below has Zo = 40 + j70 Q, Vg = 20 20 Vrms,…

Q: A 8.4m long coaxial line has following distributed parameters: R = 13 Q/m , L= 6.8 %3D %3D µH/m, G =…

A: According to the question we have to find the value of characteristic impedance.

Q: Q3: Design an L-section network to match transmission line of Zo = 50 N with the load impedance of…

Q: 10 co s(2ot +45) SP1O :A transmission line is driven by a source voltage lts = The L = 5Hm and C = 4…

Q: Q3. A 30 line is 100 km transmission line is delivering 100MW, 0.8 p.f. lag at 132kV. Each conductor…

A: Q3) A 3-ph line has, Line length= 100 km Receiving end power (Pr)= 100 MW at 0.8 lagging…

Q: Question 5 (Mapped to ILO2) A three-phase transmission line, 10 km long delivers a load of 5000 kW…

A: The solution is given below

Q: The per-phase constants of a 345-kV, three- phase, 150-km-long transmission line are resistance =…

A: we have given the per-phase constants of a 345-kV three phase 150km long transmission line are…

Q: The transmission line has the following data weight of the conductor = 8.9 kg/m, Tension in the…

A: The given tension is, T=1702 kg The weight of the conductor is, W=8.9 kg/m The sag is 5.1 m

Q: The inductances per phase and capacitance per phase of a three-phase, 50H z, 450KV transmission line…

Q: Q3: Design an L-section network to match transmission line of Zo = 50 2 with the load impedance of Z…

Q: Q4) A transmission line is 2 m long and operates at w = 106 rad/s and has = 1 rad/m, a = 4 dB/m, &…

A: Given- ωo=106 rad/sβ=1 rad/mα= 4 dB/mVs=15∠0° VZo=60+j40 ohmZg=40 ohmZL=20+j30 ohmLength, l= 2 m

Q: Use DFT method to compute the circular convolution of x(n)={4,4} and h(n)={2, 6}.

A: Given data, xn=4,4hn=2,6

Q: Q3)B-A transmission line has the following per unit length parameters: L=0.2 µH/m C=300 pF/m R=5 0/m…

A: For the given value of inductance ,capacitance, resistance and conductance we need to calculate the…

Q: The per-phase constants of a 345-kV, three-phase, 150-km-long transmission line are resistance = 0.1…

A: we need to determine the sending-end voltage.

Q: A 200 km, 3-phase transmission line has its conductors placed at the corners of an equilateral…

A: (i) The line to neutral capacitanceGiven values: -The radius of each conductor is given as r = 1 cm…

Q: Q5. A 3-phase, 50 Hz , 100 Km transmission line has conductors composed of 12 strands of Aluminum…

A: 5. 3-phase 100km transmission line: Resistivity=2.85×10-6 1+22840-20 =0.012996…

Q: Q3. A 30 line is 100 km transmission line is delivering 100MW, 0.8 p.f. Iag at 132KV. Each conductor…

Q: The parallel branches of a 2 – wire transmission line are terminated in 100 Q and 200 Q resistors as…

A: Fig: 2-wire transmission line Although for λ4 input impedance is given by Zin=z02zL

Q: has V, = 15/0° Vm Z, = A 40-m-long transmission line shown in Figure 30 + j60 N, and V, 5/-48° Vms…

Q: Example 1.2 The characteristic impedance of a uniform transmission line is 2000 ohm at frequency of…

Q: 1. A 10km Overhead transmission line is supported by two towers of 80 meters and 62 meters at a…

Q: A transmission line with the following parameters:L = 0.3 µH/m, C = 400 pF/m, R = 6 N/m and G =…

A: Given a transmission line with the following parameters, L=0.3 μHmC=400 pFmR=6 ΩmG=0.02 Smf=300 MHz

Q: A telephone line has following parameters: L=0.2pH/m, C=0.5nF/m, G=400pS/m and R=400/m. (a) If the…

A: Given R = 40 ohm/m, G = 400 micro S/m, C = 0.5 n F/m, L = 0.2 micro H/m, Calculating characteristic…

Q: Example 8.15.A3-phase, 220 kV, 50 Hz transmission line consists of 1-5 cm radius conductor spaced 2…

Q: Q3. A 30 line is 100 km transmission line is delivering 100MW, 0.8 p.f. lag at 132KV. Each conductor…

Q: Q1/ A transmission line operating at 500 MHz has Zo = 80 2, a = 0.04 Np/m, B = 1.5 rad/m. Find the…

A: Since α≠0 and independent of frequency , its a distortionless transmission line For a distortionless…

Q: Q1: A telephone cable has the following parameters R = 40 Q/m, G = 400 µS/m, C = 0.5 nF/m and L =…

A: Given telephone cable has parameters R=40 Ω/mG=400 μS/mC=0.5 nF/mL=0.2 μH/mThe operating…

Q: If the two media have equal impedances (Ni = n2), then I = . . and S = 1, and if medium 2 is a…

Q: 2- Transmission line 10m long has distributed parameters R = 52/m, L = 6µH/m, G= 10 mS/m, and C = 25…

Q: 8. A 3-phase, 230V, 50 HZ transmission line consists of 2.5 cm radius conductor spaced 2.5 meters…

Q: 1. In a transmission line terminated in a load, a rectangular pulse of 30 ns duration is introduced…

Q: Q3 The characteristic resistance of a loss-less transmission line is given by (a) 1/√LC (B)…

A: Q3 The characteristic resistance of a loss-less transmission line is given by (a) 1/√LC (B) √LC…

Q: A distortionless line has Zo- 60 0 a- 20 Np'm, -0.6c, where c is the speed of light in a vacuum. The…

A: Given parameters are:

Q: solve completely The internal resistance of the generator connected to the input of a transmission…

Q: Q3)B-A transmission line has the following per unit length parameters: L=0.2 µH/m C=300 pF/m R=5 /m…

Concept explainers

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.

Question

I need to solve a question within 20minutes as quickly as possible

Q3:
In the transmission line shown, the impedance Zin (in ohms) between node Aand the ground is
Z,= 502,1=0.5A
%3D
100n
50 n
Z, = ?
Q3: A lossy transmission line has a complex propagation constant of y
0.012+5.8 (/m). If the voltage is 12V at the generator port, what will be
the voltage magnitude when it propagates a distance of 12m?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. What is the necessary condition for matching transmission lines? In addition, what is a micro strip line? 2. For a distortion less line α = 0.02dB/m, Z0 (R0) = 60Ω and C = 0.2nF/m. Find the resistance and velocity of wave propagation. [Do not forget the units.] 3. For a finite lossless transmission line with open-circuit termination, sketch Xio vs l. Indicate where the sketch is inductive and capacitive.
. A 70 cm long lossless transmission line with characteristics impedance of 50 Ω operating at 5Mhz is terminated with a load of ?? = (65+j80) Ω. If the velocity is 0.8 times the velocity of light, then calculate (a) The reflection co-efficient, also verify the value using the given smith chart. (b) Compute the input impedance using the transmission line input impedance equation 50 Ω line is terminated with an impedance of ??= (90 – j120) Ω. Design a shortcircuited single stub matching circuit using Smith chart that is provided
A 500kV,300km,60Hz500kV,300km,60Hz, three-phase overhead transmission line, assumed to be lossless, has a series inductance of 0.97mH/km0.97mH/km per phase and a shunt capacitance of 0.0115mF/km0.0115mF/km per phase. Determine the phase constant ββ, the surge impedance ZcZc, velocity of propagation vv, and the wavelength λλ of the line. a. β=0.001259rad/km,Zc=290.43Ω,v=2.994×105km/s,λ=4990kmβ=0.001259rad/km,Zc=290.43Ω,v=2.994×105km/s,λ=4990km b. β=0.001259rad/km,Zc=290.43Ω,v=2.599×105km/s,λ=4990kmβ=0.001259rad/km,Zc=290.43Ω,v=2.599×105km/s,λ=4990km c. β=0.000629rad/km,Zc=290.43Ω,v=1.533×105km/s,λ=4990kmβ=0.000629rad/km,Zc=290.43Ω,v=1.533×105km/s,λ=4990km d. β=0.001049rad/km,Zc=290.43Ω,v=2.994×105km/s,λ=5998km
Estimate the corona loss for a 3-phase, 110 kV, 50 Hz, 150-km-long transmission line consisting of three conductors, each of 10 mm diameter and spaced 2.5 m apart in an equilateral triangle formation. The temperature of the air is 30oC and the atmospheric pressure is 750 mm of mercury. Take the irregularity factor as 0.85. Ionisation of the air may be assumed to take place at a max voltage gradient of 30 kV/cm.
A 50-ohm lossless transmission line is terminated by a 100-ohm resistive load and is operated at 100 MHz. At an electrical length of 0.8 wavelengths, what is input admittance?
A 132 kV, three-phase, 50Hz transmission line uses 18 mm diameter, equally spaced conductors. Determine the spacing between these conductors, if it is to be designed such that the corona inception voltage is 5% higher than the normal operating voltage of the line at 40oC. (You may assume the expression relating the electric field and the voltage of the line as a starting point, m=0.9)
An extra high voltage transmission line of length 300 km can be approximated by a lossless line having propgation constant is 0.00127 rad/km. The percentage ratio of line length to wave length will nearly by ?
A transmission line has an inductance of 4 mH/loop km and a capacitance of 0.004µF/km. Determine, for a frequency of operation of 1 kHz, the phase delay, the wavelength on the line, and the velocity of propagation (in metres per second) of the
A 300ᘯ transmission line is 0.8 m long and terminated with ashort circuit. The line is operating in air with a wavelength of 0.8m and is lossless. (a) If input voltage is 10V, what is themaximum voltage amplitude at any point on the line? (b) Whatis the current amplitude in the short circuit?
A 50Ω lossless transmission line is terminated with a load impedance valued ZL = RL + jXL.According to what is given, a) RL for Voltage Standing Wave Ratio to be 2What should be the relationship between XL and?b) If RL = 100Ω, find the value of XL.c) Find the voltage minimum point closest to the load on the line.
A three-phase power of 460 MW is transmitted to a substation located 500 km from the source of power. With VS=1 per unit, VR=0.9 per unit, λ =5000 km, Zc =500 V, and δ=36.878, determine a nominal voltagen level for the lossless transmission line based on Eq. (5.4.29) of the text. Using this result, find the theoretical three-phase maximum power that can be transferred by the lossless transmission line.
It is desired to construct uniform transmission lines using polyethylene (εr = 2.25) as the dielectric medium. Assuming negligible losses, find the inner radius of the outer conductor (in mm) for a 76 Ω coaxial line, where the radius of the center conductor is 0.6 (mm).