Q3: The following loads are connected to a common supply: Load A: 150 kVA at 0.707 power factor lagging. Load B: 100 kW at unity power factor. Load C: 75 KVA at 0.8 power factor lagging. Load D: 50 kW at 0.6 power factor leading. Determine the total apparent power and the overall power factor. How can you improve the power factor to unity?

Q3: The following loads are connected to a common supply: Load A: 150 kVA at 0.707 power factor lagging. Load B: 100 kW at unity power factor. Load C: 75 KVA at 0.8 power factor lagging. Load D: 50 kW at 0.6 power factor leading. Determine the total apparent power and the overall power factor. How can you improve the power factor to unity?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A building inventory identified the following equipment with the corresponding impedance or power consumption at 230 V rms. The building power supply is 230 V rms. (Assume that the building voltage supply is the reference phasor) What is the total complex power consumed within the building and the effective power factor? Load 1: 160 - j40  Load 2: 500 VA at 0.85 pf lag Load 3: 450 W at 0.95 pf lead Load 4: 200 + j300 VA
An industrial plant has an aggregate load of 99 kW. The demand factor is 54 %. If the average total energy consumption of the plant in one year is 185 MWh, what is the yearly load factor of the plant? (Note: Aggregate is synonymous to Connected Load).
A factory has an electrical load of 1600 kW at a lagging powerfactor of 0.8. An additional variable power factor load is to be added tothe factory. The new load will add 320 kW to the real power load of thefactory. The power factor of the added load is to be adjusted so that theoverall power factor of the factory is 0.96 lagging. Assume the factory described above is fed from a linehaving an impedance of 0.05+j0.4 Ω. The voltage at the factory ismaintained at 2400 V(rms). 1. a) Find the average power loss in the line before and after the loadis added.2. b) Find the magnitude of the voltage at the sending end of the linebefore and after the load is added.
In a chopper circuit the supply power of 2834 W and efficiency is 43 %. Calculate the load power obtained in the circuit a. 1219 W b. 12186 W c. 2834 W d. 2838 W
Problem : In the case of an industrial load with a power factor of 0.707 lagging, consuming 100 kW, and the line voltage at 60 Hz is 480Vrms, with a line resistance of 0.1Ω between the power company's transformer and the load, calculate the amount of power saved if the load's power factor changes to 0.94 leading. The answer is "3.771 Kilo-Watt has been saved" and also I want to know the concept of 'Power Factor'.
A supply voltage Vs with magnitude of 230 Volt RMS with 60 Hz frequency and a phase angle of zero degrees is connected in parallel configuration to two loads each load consumes power as following: Load 1: 30 K watts with Power factor of 1. (PF= 1) Load 2: 5 K VA (apparent power) with Power factor of 0.86 (PF = 0.86) lagging. (Note that lagging PF means the difference between phase of the voltage and phase of the current is positive) A. (10 pts) The complex power consumed by each load B. (10 pts) The current drawn by each load from the source.
In the given circuit, the amplitude of the input voltage is 180 Volts RMS and its phase is 45 degrees.The power values that the loads receive/give are given below.What is the phase of the current phasor I0?Load 1 = 1.8 kW and capacitive 1.2 kVAR8 kW with load 2 = 0.5 back power factorLoad 3 = 3 kVA with 0.9 forward power factor
The load at a certain factory consists of the following:10 kW, pf = 0.6 lagging15 kW, rf = 0.5 lagging25 kVA, pf = 0.75 lagging15 kVAR, pf = 0.8 lagging22 kW5 kVAR, pure inductanceTotal True Power = 85.75 kWTotal Reactive Power = 58.5295 kVArTotal Apparent Power = 103.8208 KVA1. The power factor is to be corrected to 0.95 lagging. If resistive heating units were used instead, determine the real power rating of these devices. Ans = 92.32222. The power factor is to be corrected to 0.95 lagging. If a synchronous motor is to be used instead, determine the real power rating of this motor if its power factor is 0.6 leading. Ans = 18.257
If the voltage and current given below are suppliedby a source to a circuit or load, determinea. The power supplied by the source which isdissipated as heat or work in the circuit (load).b. The power stored in reactive components in thecircuit (load).c. The power factor angle and the power factor.˜VS = 7∠0.873 V ˜IS = 13∠(−0.349) A
PLS USE 4 DECIMAL PLACES FOR THE FINAL ANSWERS An inductive reactance of 10 ohms is connected in parallel with the capacitive reactance of 30 ohms. If the combination is connected in series with a 10 ohm resistance. The given voltage is 200V. *What is the total real power of the system in magnitude with unit of kW? *What is the total real power of the system in magnitude with unit of kVAR? *What is the total impedance in polar form in ohms? *What is the total real power of the system in magnitude with unit of kVA? *What is the total current in polar form in A?
Calculate the average power abosorbed by each passive component in the circuit diagram and determine the total average power supplied by the current source. (Given answer : P3Ω=56.60W, P4Ω=33.96W, PL=0, PCS=90.50W)
Q3: A power supply is having the following loads: Type of load Maximum demand (kW) | Diversity of group | Demand factor Domestic 15000 125 0.8 Commercial 25000 1.2 1 Industrial 50000 13 0.5 If the overall system diversity factor is 1.5, determine: 1. The maximum demand. 2. Connected load of each type.