Q4: Design a ladder logic program to run the three Motors:(Y0= oil pump motor, Y1 = auxiliary motor, Y2= main motor)according to the following information:The ON/OFF sequence of all three motors should be as per tablegiven below. The sequence should continue till start input is present.In addition, stopping all motors immediately when STOP is pressed.Motors ON/OFF Sequence TableTime In SecondsMotors0-55-1010-1515-2020-2525-30YOONONONOFFOFFOFFY1OFFOFFSONONSONOFFY2ONOFFOFFOFFONONOIL MotorAuxillary MotorMain MotorPage 3 of 3START XOSTOP X1

Here's a ladder logic program that runs the three motors (Y0 = oil pump motor, Y1 = auxiliary motor,…

Answered: Q4: Design a ladder logic program to…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is Mealy state machine. Draw the state diagram of sequence 1010 using mealy machine.
23. In a DC servo motor system, the tachometer feeds back a voltage that's proportional to motor speed. Where does this voltage go to? A. The driver B. The interpolator card C. The axis logic card D. The CPU in the main controller xis logic card for a stepper motor system and are used to
8. What instruction would you select for each of the following discrete input field devices to accomplish the desired task? (State the reason for your answer.) a. Turn on a light when a conveyor motor is running in reverse. The input field device is a set of con- tacts on the conveyor start relay that close when the motor is running forward and open when it is running in reverse. b. When a pushbutton is pressed, it operates a so- lenoid. The input field device is a normally open pushbutton. c. Stop a motor from running when a pushbutton is pressed. The input field device is a normally closed pushbutton. d. When a limit switch is closed, it triggers an instruc- tion ON. The input field device is a limit switch that stores a 1 in a data table bit when closed.
Write a ladder program for a washing machine with the following specification: The machine has two push-button switches A and B for turn on and off the machine respectively. The machine has two sensors for weighting, the sensors given the following reading: - Sensorl ON ON OFF OFF Sensor2 ON OFF ON OFF weight 25 KG 20 KG 5 KG 0 KG
The amount of short-circuit current from a motor is equal approximately to_current for each motor. A.accelerating b. locked-rotor c. stator d. final
we are interested in an automatic garage gate system for a building. This system includes a gate that goes up or down, a motor to actuate the gate (pull, push) and sensors to collect information (gate open contact, gate closed contact). The sensors are all similar, each signaling to its controller that a contact has taken place. The user has a remote control to control with just two buttons: open, close. The operating principle of the system is as follows. Suppose the gate is closed. The user opens the gate by pressing the Open button on his remote control. He can stop opening by pressing the Open button again, the motor stops. Otherwise, the gate opens completely and triggers a Gate Open sensor which causes the motor to stop. Pressing the Close button causes the gate to close if it is open (partially or fully). The closing can be stopped by pressing the Close button again, the motor stops. Otherwise, the gate closes completely and triggers a Gate Closed sensor which causes the engine…
Subject-power electronic Define A.Delay time B.Rise time C.reverse recovery voltage D.spread time.
Subject: Digital Logic Design An aircraft’s functional monitoring system. A circuit is required to indicate the status of the landing gears prior to Take off. The plane has three landing gear: right, left and center. After the takeoff, the pilot will activate ‘gear up’ switch to retract the landing gear. Assume that has been done. A green LED will turn on in the cockpit only if all three landing (03) gear are properly retracted. A red LED will turn on if any of the three (03) landing gear fail to retract properly after takeoff. When landing gear is properly retracted, a corresponding sensor will provide High voltage to a logic circuit. When a landing gear has failed to retract properly, the sensor provides a Low voltage signal to the logic circuit. Design and implement the circuit of the system with the help of logic gate.
Required information A fan is to run only when all of the following conditions are met: • Input A is OFF. • Input B is ON or input C is ON, or both B and Care ON. • Inputs D and E are both ON. . One or more of inputs F, G, or H are ON. Saved Note: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Identify the correct typical PLC ladder logic diagram for the given control system. Multiple Choice
9- Controlled variable is the output of a. Plant b. Controller c. None of the above d. Error Detector
What is the meaning of “ON DELAY” in Time relay RXKL at AC-operation . (Explain Briefly)
Sub-Parts A,B and C, have been solved by a Bartleby expert earlier, and told me to post the question again for the rest of the question to be solved ( D, E ). Course: EE350 ( system dynamics and control ).

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS