Q4- Determine the following properties for the gas given below at 542O psig and 257°F. - value of z-factor - gas specific gravity - gas density - specific volume - isothermal gas compressibility - gas formation volume factor - gas viscosity - gas expansion - * -gross heating value Composition, mole percent Component Hydrogen sulfide Carbon dioxide Nitrogen Methane Ethane Propane i- Butane n-Butane i- Pentane n-Pentane Hexanes Heptanes plus 20.90 44.69 1.22 21.80 3.68 2.05 0.58 1.09 0.46 0.56 0.72 2.25 100.00 Properties of heptanes plus Specific gravity Molecular weight 0.844 115 lb/lb mole

Q4- Determine the following properties for the gas given below at 542O psig and 257°F. - value of z-factor - gas specific gravity - gas density - specific volume - isothermal gas compressibility - gas formation volume factor - gas viscosity - gas expansion - * -gross heating value Composition, mole percent Component Hydrogen sulfide Carbon dioxide Nitrogen Methane Ethane Propane i- Butane n-Butane i- Pentane n-Pentane Hexanes Heptanes plus 20.90 44.69 1.22 21.80 3.68 2.05 0.58 1.09 0.46 0.56 0.72 2.25 100.00 Properties of heptanes plus Specific gravity Molecular weight 0.844 115 lb/lb mole

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Convert: Convert a (15.5 °C+ 17) temperature into °F temperature.
Refer to Fig. 1214. The 3′′diameter orifice has coefficients of velocity and contraction of 0.950 and 0.632, respectively. Determine (a) the flow for the deflection of the mercury indicated and (b) the power in the jet.
Orifice Given:As = 3m2C = 0.92Ao = 0.01m2 Determine the time for the depth of liquid in the tank to be 0.8m
Given: As = 3m2 C = 0.92 Ao = 0.01m2 Find: Determine the time for the depth of liquid in the tank to be 0.8m
A heating plant for a large medical campus requires 5506 MBH (1MBH \= 1,000,000 btuh) of heating capacity. Which of the following pipe size and velocity in feet per second (fps) for the main would be needed if the plant is a 62 psig medium-pressure steam system? (Hint: Table 7.2) a.8" pipe at 130 fps b.4" pipe at 150 fps c.2" pipe at 100 fps d.4" pipe at 130 fps e.5506 MBH; 62 psig
Glycerin (s.g.=1.26, and absolute viscosity = 1.49 Pa-s) flows through a rectangular conduit 325mm by 450mm at the rate of 160 lit/sec. Determine the major head loss due to friction (hf) per 1km length of pipe.
Compute the pressure heat at m, in feet of fluid A, indicated by open manometer in figure 2 below when (a) Fluid A is oil (sp gr 0.851), the gage liquid is carbon tetrachloride (sp gr 1.51), y=30.15 in, z=3051 in. (b) Fluid A is molasses (sp.gr 1.50), gage liquid is water, y=3.51 ft, z=1.15 ft
Compute the pressure heat a m, in feet of fluid A, indicated by open manometer in figure below when; (a) Fluid is oil (sp gr 0.895), the gage liquid is carbon tetrachloride (sp gr 1.95), y = 30.75 inch, z = 30.95 in(b) Fluid A is molasses (sp gr) 1.50), the gage liquid is water, y = 3.95ft, z = 1.75ft Note: Clear handwritten solution
Air at 30 deg. Celsius and 110KPa flows at 20N/s through a rectangular duct that measures 160mm x 320mm. Compute the average velocity (m/s) and flow rate (? ^3/s) using gas constant equal to 289 J/kg-K.
A 2 1⁄2 - in. fire hose discharges water through a nozzle having a jet diameter of 0.97 in. the lost headin the nozzle is 5 percent of the velocity head in the jet. If the gage pressure at the base of the nozzle is 60 lb.per sq. in.: (a) compute the discharge in gallons per minute (1ft3 = 7.48gal); (b) what is the maximum horizontalrange to which the stream can be thrown (neglecting air resistance)? (c) what is the maximum possibletheoretical height that the jet can reach and at what angle?
Engine oil (similar to oil D) flows at 0.95 ft/s through a 1-inch diameter tube. The bulk oil temperature is 320 F and the tube surface temperature is 300 F. Determine the unit convective coefficient for tube lengths of (a) 6.5 ft and (b) 13 ft (round off answers to 1 decimal place). For oil, k = 0.94 Btu-in/ft2-hr-F and cp = 0.52 Btu/lb-F.
The saturated liquid of water at T=300C has total volume (v) of 0.05m3,quality(x) of 75%,vf=1.4036×10-3m3/kg,vg=0.02167m3/kg A.find the specific volume v in m/kg of two phase mixture B.find the mass (m) of water in kg C.find the mass(mg) of the satured vapor in kg D.find the mass(mf) of the satured liquid in kg