Q4: the modulation index of the modulatedsound signal of 0.5, while the maximumvoltage of this signal is 12 volts. themodulated waveform was affected by 30ohm as an impedance to pass through thissystem, let the modulating and carrierfrequencies are 200 and 4KHZ respectively.calculate 1- the transmitted and modulatedpower of this signal. 2- the efficiency of thissystem 3- write the mathematical model ofinput and output signals with its real values.4- draw the waveform of the modulated* signal

It's given that, Modulated sound signal, μ=0.5The maximum voltage of the signal, Am=12…

Q4: the modulation index of the modulated sound signal of 0.5, while the maximum voltage of this signal is 12 volts. the modulated waveform was affected by 30 ohm as an impedance to pass through this system, let the modulating and carrier

Q4: the modulation index of the modulated sound signal of 0.5, while the maximum voltage of this signal is 12 volts. the modulated waveform was affected by 30 ohm as an impedance to pass through this system, let the modulating and carrier

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: At what junction offset are varicaps used

A: Given : varicap is a PN junction diode which will works only in the reverse biased region. In…

Q: DISCUSSIONS: 1) What is the Darlington Pair? and what is the main features of it?. 2) From your…

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Q: (d) What is the ac collector resistance, rc? Express the value in

A: The required parameters can be calculated by using AC analysis of the amplifier

Q: (II) What is the input resistance seen by the signal source?

A: We need to find out input impedance for given circuit

Q: Q2-which one is preferred AM-SSB or AM-DSB ? and explain why.

A: The explanation is as follows.

Q: List out any two problems that may occur in the reconstruction of the original signal and suggest…

A: Problems that may occur in the reconstruction of the original signal are Intersymbol interference…

Q: Q4 Derive a formula for the output resistance of the current mirror in Figure 4 and show that this…

A: Note: We are authorized to answer one question at a time since you have not mentioned which question…

Q: It is requested to determine the operating point of the transistor by drawing the DC load line.…

A: Detail solutions in the image

Q: Use own words to clearly explain the interference phenomena of a) signal loss by frenquency out of…

A: Signal loss by frequency out of range is generally occurred in computers when input signal is loss…

Q: In analog to digital signal conversion sampling, what is problems that may occur in the…

A: An analog signal can be converted to a digital form or vice versa through a series of steps. The…

Q: A) What does VCO stand four? Show by drawing the relationship between its input and output signals.…

A: VCO stands for Voltage-Controlled Oscillator This is an oscillator whose output frequency is…

Q: Derive the expression for the second order system for the value of ζ >1, when subjected to unit…

Q: What is the output peak voltage during the positive alternation of the input signal for the circuit…

A: In this question we will write about output peak voltage positive input....

Q: Q4: a- many methods are used for extracting the modulating signal from the frequency modulation…

A: Since you have asked two question and not specified which one to answer I will answer 1st question…

Q: Discuss the effect of changing the frequency of input analog signal on the reconstructed analog…

A: The reconstruction of the analog output signal is the process of getting back the signal from the…

Q: The power dissipation of a transistor with no signal input in class A power amplifier is usually…

A: Classification of DC quiescent power in Class A power amplifier?

Q: In time the use of the ________ became the more desirable approach because an important parameter of…

A: There are few parameters which has different applications and their different advantages. Some of…

Q: Q4. A) Compare the operation of a series modulator eircuit with a collector modulator circuit in AM…

A: Series Modulator Here the modulating signal is applied to the emitter follower. This emitter…

Q: Derive the expression for the first order system, when subjected to unit ramp input signal.

A: Considering a first order system The transfer function of the first order system is given below,…

Q: Problem-1 Consider a low-pass analog signal of 8 kHz. What is minimum bandwidth, assuming 4 bits per…

A: Given:Low- pass analog signal of 8 kHz.To find:Minimum bandwidth for 4 bits per sample.Minimum…

Q: Q2: Suppose a signal illustrates below. This analog information signal has to be quantized using…

Q: IGBT is a short form of Insulated Gate Bipolar Transistor, combination of Bipolar Junction…

A: The comparison table on above characteristic is given below

Q: \ discuss a conversion of an analogue signal to digital bits Please I need to resolve the question…

A: The analog to digital converter converts the analogue signal to digital bits by the process of…

Q: Describe different control schemes of AC regulators and derive the expressions of average and…

A: AC regulators- This is an electronics device. This is based on electronics devices like SCR, TRIAC,…

Q: or the common emitter amplifier circuit in Figure Q4(a), determine the low cut- ff frequency for…

Q: a. A system is provided in Block Diagram form as shown in figure 4, draw its equivalent system in…

A: The given block diagram can be reduced by considering the parallel connected and cascade connected…

Q: What values of β correspond to α = 0.970, 0.993, 0.250? (b) What values of αcorrespond to β = 40,…

A: The expression for the common emitter current gain is given as, For α=0.970 β=α1-α=0.9701-0.970=32.3…

Q: Construction and analysis of common collector amplifier on Uni-train system

Q: A common emitter class A transistor power amplifier uses a transistor with B=100. The load has a…

Q: a. Draw the block diagram of a measurement system. b. Mention the function of signal processing…

A: Measurement system is used to measure a quantity and compare that with the standard quantity.

Q: QUESTION 4 In this voltage divider bias circuit, the input is at the base. Output is at the emitter…

A: Given: In this voltage divider bias circuit, the input is at the base. Output is at the emitter with…

Q: Figure 4 (for numbers 20 to 24) RSIG V₁ Z₁ RG ở VDD ww www RD Rs 70 RL

A: As per the guidelines of bartleyby I need to answer first three subparts only so kindly repost other…

Q: For the common emitter amplifier circuit in Figure Q4(a), determine the low cut- off frequency for…

Q: With sketch, write about «TIE-LINE BIAS CONTROL"

A: TIE-LINE BIAS CONTROL - The tie-line bias control (TBC) approach has been commonly employed in…

Q: For voltage divider configuration as shown in Figure Q1 (b), sketch the diagram of small signal…

Q: Explain any two signal presentation (Final Element) in measurement system with neat diagrams.

A: Signal presentation is a last step of (Final element) of measurement system. There are different…

Q: Sketch and describe mathematically the even and odd components of the signal shown in Figure (1)

A: given signal

Q: explain any two signal presentation (final element) in measurement system with neat diagram.

A: the value of a quantity determined by a certain device is called a measuring instrument. An…

Q: 2. Mention the advantages of indirect method of FM generation?

A: 2) There are various advantages of using indirect method to generate FM signal.

Q: Define signal

A: The signal carries the messages from one person to another or from one place to another. In…

Q: Explain any two signal presentation (Final Element) in measurement system with neat diagrams.

Q: The conduction angle of class A amplifier is ?

A: The explanation is as follows.

Q: The figure below of signal flow graph shown has: 3 4 6. 5. 2.

A: Given

Q: Give the formula for modulation index and explain its terms

Q: Write the expression for the output voltage of a balanced modulator

A: A balanced modulator circuit is an electronic circuit which is used to produce double sideband…

Q: Explain signal and system

A: A sign is a depiction of how one boundary differs with another boundary. For example, voltage…

Q: what is darlington pair

Q: Mention 4 factors out of many factors that must be considered and become necessary data in the…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Q4) (a) Explain what is meant by the term, modulation, and produce a diagram of an Amplitude…

A: We need to explain what is meant by modulation and also need to give a diagram of an amplitude…

Question

Q4: the modulation index of the modulated
sound signal of 0.5, while the maximum
voltage of this signal is 12 volts. the
modulated waveform was affected by 30
ohm as an impedance to pass through this
system, let the modulating and carrier
frequencies are 200 and 4KHZ respectively.
calculate 1- the transmitted and modulated
power of this signal. 2- the efficiency of this
system 3- write the mathematical model of
input and output signals with its real values.
4- draw the waveform of the modulated
* signal

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. The output stage of a transmitter requires, owing to supply voltage limitations, a downward impedance transformation of the antenna resistance. The load impedance is 50-Ω. Suppose we wish to deliver 3 Watts of power into such a load at 915 MHz, but the power amplifier has a maximum peak-to-peak sinusoidal voltage of only 7 Volts because of various losses and transistor breakdown problems. Design a two section L-match of low pass type to allow that 3 Watts to be delivered to the 50-Ω load. Assume that all reactive elements are ideal.
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
For the transistor , IS = 6×10−16 μA,αF = 0.985, and αR = 0.25. (a) What type oftransistor is in this circuit? (b) Label the collector, base, and emitter terminals of the transistor.(c) Label the emitter-base and collector-base voltages, and label the normal direction for IE , IC, andIB. (d) Write the simplified form of the transportmodel equations that apply to this particular circuitconfiguration. Write an expression for IE /IC. Writean expression for IE /IB. (e) Find the values of IE ,IC, IB, βF , βR, VE B, and VC B.
2. Mention the advantages of indirect method of FM generation? 4.
For the transistors in this question, use |Vt| = 0.1V, |VA| = 10V, kn,p = 12.5mA/V2. The signal source has 0.1 mV amplitude and 1 kHz frequency. Calculate Rout, Gm and Av for the circuits separately ?
Define Small signal Stability. Why is it important to study in a power system network? How Ts and Td , these tow torques are very important to determine the small signal stability of a network?
What is the purpose of balanced ring modulator in single-sideband transmission? Describe its operation.
Suggest a repair scheme and precautions to be observed while replacing the transistor, considering the parameters of the component from the data sheet.
Noise generated by an amplifier of radio is an example for?
The Ebers-Moll model was one of the first mathematical models used to describe the characteristicsof the bipolar transistor. Show that the npn transportmodel equations can be transformed into the EbersMoll equations below. [Hint: Add and subtract 1from the collector and emitter current expressions.]
Define the following conceptsa. Positive modulation percentageb. Modulation efficiencyc. Signal strengthd. At least one technique for building an AM transmitter.
Mention 4 factors out of many factors that must be considered and become necessary data in the design of the power transfer system, explain.