Q5: A directional coupler has the scattering matrix given below. Find the return loss, coupling factor, directivity, and insertion loss. Assume that the ports are terminated in matched loads. [S] = 0.15245° 0.85/90° 0.22180° 0.006290°- 0.85290° 0.15245° 0.006290° 0.22180° 0.22180° 0.006290° 0.15445° 0.85/90° L0.006290° 0.22180° 0.85290° 0.15/45°

Q5: A directional coupler has the scattering matrix given below. Find the return loss, coupling factor, directivity, and insertion loss. Assume that the ports are terminated in matched loads. [S] = 0.15245° 0.85/90° 0.22180° 0.006290°- 0.85290° 0.15245° 0.006290° 0.22180° 0.22180° 0.006290° 0.15445° 0.85/90° L0.006290° 0.22180° 0.85290° 0.15/45°

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How large dish diameter is needed for 80 dB gain at 300 MHz?
Q. A base stationcellular communicationsystems lossless antenna has a maximum gain of 16 dB (above isotropic) at 1,900 MHz. Assuming the input power to the antenna is 8 watts, what is the maximum radiated power density (in watts/cm2 ) at a distance of 100 meters? This will determine the safe level for human exposure to electromagnetic radiation.
Determine the isotropic free space loss at 8 GHz for the shortest path to a geostationary satellite from Earth (36000 km)
Find the basic path loss for a communication link from Moon to Earth operating at 4000 MHz. The distance between Moon and Earth is 384000 km.
An attenuator can be made using a section of waveguide operating below cutoff, as shown in theaccompanying figure. If a = 2.286 cm and the operating frequency is 12 GHz, determine the requiredlength of the below-cutoff section of waveguide to achieve an attenuation of 100 dB between the inputand output guides. Ignore the effect of reflections at the step discontinuities.
a) A parallel plate transmission line has plate separation d=1 cm, and isfilled with teflon having dielectric constant ε’r=2. Determine themaximum operating frequency such that only TEM mode willpropagate. Also find the range of frequencies over which TE1 andTM1 modes will propagate and no higher order modes. b) In the parallel plate waveguide of part -a, the operating wavelength isλ=2mm. How many waveguide modes will propagate?
Satellites A and B have the same communication equipment (transmitter, antenna, etc.) onboard to communicate with the same ground station. If satellite A is in an orbit 1000 Km higher than satellite B, which will have a poorer signal-to-noise ratio? Why?
A geo-synchronous satellite is transmitting a TV signal to an earth based station at a distance of 40,000km. Assume that the dish antennas of the satellite and the earth station have the diameter of 0.5m and 5m, and aperture efficiency of 60%. If the satellite’s transmitted power is 6W and the downlink frequency is 4 GHz, calculate the antenna gain in dB and the amount of received power.
In line-of-sight radio system, losses are mainly due to free space path loss (FSPL). FSPL is proportional to the square of the distance between the transmitter and receiver as well as the square of the frequency of the radio signal. Observe the FSPL for the situation below. a) For fixed frequency at 2600 MHz, calculate and sketch the graph of FSPL at the range of 1 km, 10 km, and 30 km. b) For fixed frequency at 5.8 GHz, calculate and sketch the graph of FSPL at the range of 1 m, 10 m, 100 m and 1 km.
What is the maximum frequency (in GHz) that a single-line bus with a length of 1 meter can operate at without experiencing significant signal degradation, assuming a rise/fall time of 10% of the signal period and a characteristic impedance of 50 ohms?
Question)The coupling factor and isolation of a lossless, symmetric directional coupler are 8 dB and 20 dB respectively. Determine the scattering matrix of the directional coupler. Also determine the directivity of the device? This Question from Microwave systems course.
A 5.0 × 2.0 mm2air-filled rectangular waveguide is to operate below85 GHz. Determine the number of TE and TM modes that can be transmitted in the waveguide. Subsequently, sketch the cross-sectional view of field line distributions for TE10, TE11, and TM11 modes.