Q5: An object consist of two pieces. The mass of one piece has been measured to be (6 kg). The volume of second piece, which is made from aluminum, has been measured to be (4.44*10^-4 m^3). A handbook lists the density of aluminum as (2.7*10^3 kg/m^3). What is the total mass of the object

Q5: An object consist of two pieces. The mass of one piece has been measured to be (6 kg). The volume of second piece, which is made from aluminum, has been measured to be (4.4410^-4 m^3). A handbook lists the density of aluminum as (2.710^3 kg/m^3). What is the total mass of the object

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The object W1 in the figure is at an angle of 45 to the horizontalIt is based on its frictionless surface at point B.Point A is articulated (fixed support) and ground frictionSince (μ = 0.3) body W2 is a surfaceWhat should be the weight of W1 that will cause it to start? W2= 38 [kN]sin45=cos45=0.7
9. A gutter with trapezoidal cross section is to be made from a long sheet of tin that is4√108 inches wide by turning up √108 inches on each side. What is the depth of thegutter for the greatest carrying capacity? Give your answer in exact form(not decimalform). 10. At what rate is the vertex angle of a right circular cone changing when the radius is 3 ft andthe altitude is 4 ft if the altitude is increasing at 6 inches per min and the radius is constant?
Water from a reservoir flowing through a non rigid 600mm diameter pipe with a velocity of 2.90m/s is completely stopped by a closure of a valve situated 1050m from the reservoir. The pipe thickness is 18mm. Bulk modulus of elasticity of water is 2090MPa and modulus of elasticity of steel is 200090MPa. Compute the velocity of soundwave 1425.90 1524.09 1245.09 1952.09 Determine the pressure due to instantaneous closure (KPa) 3106.75 1360.57 3610.75 6301.57 Determine the pressure due to a closure that takes place in 5 seconds. in KPa 1821 1218 1128 1812
Convert 8,365 cm3 to ft3 (Answer to 3 decimal places) (2.54 cm= 1 inch); (12 inch= 1ft)
An engineer used a 30 m tape in measuring an inclined ground 459.20 m long. The difference between the starting point and end point is 1.20 m. The tape is of standard length at a temperature of 100 C and a pull of 50 N. During measurement the temperature reading was 15 0 C and a pull of 75N applied at both ends. A= 6.5mm2 ; E = 200GPa; K = 0.0000116 m/C0 . The mass of the tape is 0.075kg/m. Determine the horizontal distance.
The reading of an automobile fuel gage is proportional to the gage pressure at the botoom of the tank. If the tank is 32 cm deep and is contaminated with 3cm of water. A.) If the tank is full of gasoline what should be the reading at the page in Pa? Use Ywater=9790N/m^3, Ygasoline=6670N/m^3 and Yair=11.8N/m^3 Choices: 1934,2839,3132,2134 B.) How many centimeters of air remains at the top when the gauge indicates full? Choices: 3.75,1.41,4.42,2.36 C.) If the tank is 0.5m^2 in area, calculate the volume of gasoline when the gage reads full Choices: 138 L,160L,145L,123L
Knowing that at the instant shown assembly A has a velocity of 9 in./s and an acceleration of 15 in./s2both directed downward, determine (a) the velocity of block B, (b) the acceleration of block B
A block of wood 0.56 m x 0.56 m x “h” meters in dimension was thrown into a liquid with SG = 2.078. It floats with 0.29 m projecting above the water surface. The same block was thrown into a container of a liquid having a SG of 1.8 and it floats with 0.18 m. projecting above the liquid surface. Determine the value of 'h' in meters. Round off to two decimal places.
Fluid Mechanics. Reg.no : 5395 Pb # 3: Refer to Figure 2. Assume that friction is negligible, that θ = 115o, and that the water jet has a velocity of (Reg.No/100) m/s and a diameter of 60 mm. Find (a) the component of the force acting on the blade in the direction of the jet; (b) the force component normal to the jet; and (c) the magnitude and direction of the resultant force exerted on the blade. Note: Assume reasonable values for any missing data. Symbols have usual meaning unless otherwise stated.
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?
Convert 100 min/cm^3 to m^3/h
A cylindrical tank is having hemispherical base. The height of cylindrical portion is 4 m and the diameter is 3 m. At the bottom of this tank an orifice of diameter of 300 mm is fitted. Find the time required to completely emptying the tank. Take Cd= 0.60. a. 127 seconds b. 175 seconds c. 145 seconds d. 217 seconds