Digital Signal ProcessingK = 20, P = 6, Q = 6 Q5. Impulse response of an FIR filter is given byh[n] =sin(0.7¤n)_ sin(0.2rn)The input to the filter is given byx[n] = K + P cos(0.87n – 0.57 ) + Q cos(0.5tn + 0.2n )(a) Draw the frequency response of the filter and DTFT of x[n].(b) Determine its output, y[n].

The impulse response of an FIR filter is given as hn=sin0.7πnπn-sin0.2πnπn ...1. The input to the…

Q5. Impulse response of an FIR filter is given by h[n] = sin(0.7xn) _ sin(0.2#n) The input to the filter is given by x[n] = K + P cos(0.8tn – 0.5x ) + Q cos(0.5tn+ 0.2n) (a) Draw the frequency response of the filter and DTFT of x[n].

Q5. Impulse response of an FIR filter is given by h[n] = sin(0.7xn) _ sin(0.2#n) The input to the filter is given by x[n] = K + P cos(0.8tn – 0.5x ) + Q cos(0.5tn+ 0.2n) (a) Draw the frequency response of the filter and DTFT of x[n].

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Let the impulse response of a filter be ℎ[?] = {ℎ[0] = −0.5, 0.5}a) Calculate the frequency response ?(???). Is it a low-pass or a high-pass filter? Plot boththe magnitude and phase responses.b) Obtain the I/O relation for this filter.c) Is this a causal filter? Explain your answer.
DESIGNPROBLEM_PSPICEMULTISIM Use a 500 nF capacitor to design a bandreject filter, as shown . The filter has a center frequency of 4 kHz and a quality factor of 5. 1. a) Specify the numerical values of R and L. 2. b) Calculate the upper and lower corner, or cutoff, frequencies in kilohertz. 3. c) Calculate the filter bandwidth in kilohertz.
DESIGNPROBLEM_PSPICEMULTISIMUsing a 5 mH inductor, design a high-pass, RL, passive filter with a cutoff frequency of 25 krad/s . 1. a) Specify the value of the resistance. 2. b) Assume the filter is connected to a pure resistive load. The cutoff frequency is not to drop below 24 krad/s. What is the smallest load resistor that can be connected across the output terminals of the filter?
For the following bandpass filter circuit, select the circuit elements in order to satisfy the following specifications: fl= 100Hz fu= 200Hz First, consider the lowpass filter on the left, which has a transfer function Hw= Rf1/R11 1/Rf1C1jw+1 The desired lowpass transfer function, written in hertz frequency, is H(w)= -1/(jf/fu+1) If R1 is selected to be 1000Ω then determine R11 in ohms. Enter R11. Omit the units. (hint: remember to convert between fand w when needed) Referring to question 1, what is C1 in μf Consider the highpass filtter on the night, which has a transfer function H(w)= - Rf2/R12 R12/C2jw/R12C2jw+1.The desired highpass transfer function is -if/ft/if/ft+1. If R12 is selected to be 1000Ω then determine Rf2 in ohms and C2 in μf.Enter Rf2 (hint: remember to convert between fand w when needed) Referring to problem 3, what is C2 in μf
DESIGNPROBLEM_Using a 100 nF capacitor, design a highpass passive filter with a cutoff frequency of 300 Hz. 1. a) Specify the value of R in kilohms. 2. b) A 47 kΩ resistor is connected across the output terminals of the filter. What is the cutoff frequency, in hertz, of the loaded filter?
A resistor, denoted as Rl, is added in series with the inductor in the circuit . The new low-pass filter circuit is shown. 1. a) Derive the expression for H(s) where H(s)=Vo/Vi. 2. b) At what frequency will the magnitude of H(jω) be maximum? 3. c) What is the maximum value of the magnitude of H(jω)? 4. d) At what frequency will the magnitude of H(jω) equal its maximum value divided by 2? 5. e) Assume a resistance of 75 Ω is added in series with the 10 mH inductor in the circuit. Find ωc, H(j0), H(jωc), H(j0.2ωc), and H(j5ωc).
The response of a Butterworth filter is required to fulfill the following specifications: f_{p} = 1000Hz fs = 5000 Hz, A_{p} = 2dB A_{s} = 40dB Determine the following (i) Minimum filter order required to satisfy these specifications (ii) The 3dB corner frequency for this filter (iii) The transfer function of the filter H(s) b. Synthesize the filter described in part (a) above by continued fraction expansion to give a lossless ladder network terminated at both ends with 600 resistor. Draw the circuit.
A measurement to be used to measure the voltage numerically in electrical energy systemssystem, according to time expressionv= 311sin (314t) + 50sin (1570t + 20o) + 40sin (3454t + 30o) (V)A voltage sign is applied. The analog filter in this measuring systemIt is meant to pass the last component in the voltage expression, destroying the first and second component. First order RC filter will be designed for the above measurement system. Draw the circuit of the filter. Infer the transfer function.
Consider the circuit shown . 1. a) What is the transfer function, H(s)=Vo(s)/Vi(s), of this filter? 2. b) What is the cutoff frequency of this filter? 3. c) What is the magnitude of the filter’s transfer function at s=jωc?
a ) Using 0.1 pF capacitors , design an active broadband first - order bandpass filter that has a lower cutoff frequency of 200 Hz , an upper cutoff frequency of 2000 Hz , and a passband gain of 0 dB . b ) Write the transfer function for the scaled filter . c ) Use the transfer function derived in part ( b ) to find H ( wo ) where wo is the center frequency of the filter . d ) What is the passband gain ( in decibels ) of the filter at wo ?
An analog filter with magnitude response shown in the image, is converted to a discrete-time filter using the bilinear transformation with Ts = 0.3. Sketchby hand the resulting magnitude response | H(ω) |. Label all critical frequencies and amplitudes
(a) as shown for a maximally flat second-order low-pass filter with fo =25 kHz, using the circuit as shown. Assume C =0.005μF.What is the filter bandwidth? (b) Use frequency scaling to change fo to 50 kHz.