Q5b): Three reservoirs A, B and C are connected as shown in Figure below. The water elevations in reservoirsA, B and C are 100 m, 80 m and 60 m respectively. The three pipes connecting the reservoirs meet at junction,J. Pipe AJ is 900 m long, BJ 800m long, CJ 700m long and the diameter of all pipes equal to 850 mm. If allpipes are made of ductile iron. Find the flow rate in each pipe. Use fequal to 0.0235 for all pipes.E.L. 100 mE.L.-80 mвLAJ- 900 mE.L.-60 mLBJ 800mLIC- 700m

hf=0.0826fLQ2/D5 hf1=0.08260.0189000.023520.855=0.00073890.4437= 0.00166=1.66mElevation P,=Elevation…

Answered: Q5b): Three reservoirs A, B and C are…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A new 45 cm cast-iron pipe 600 m long carries 260 litres/s from reservoir A, discharging into two new cast-iron pipes each 500 m long. One pipe is 30 cm in diameter and leads to reservoir B, in which the water surface is 5 m lower than in A. If the water surface in C is 7 m lower than that at A, determine the diameter of the pipe leading to C. Use n 0.011.
The system shown below consists of 1000 m long and 50 mm diameter cast iron pipes. With a volume flow of 5 L/s at 20°C from the first point100 m highCalculate the gauge pressure required to transport water to the reservoir.
A 170-m long pipeline, composed of two pipes connected in series, discharges freely at a point 40 m below the water level at intake. The pipe projects into the reservoir. The first 100 m is 25 cm in diameter, and the remaining 70 m is 15 cm in diameter. Assuming that f=0.05 for both pipes, (a) find the rate of flow. If the junction of the two sizes of pipe is 25 m below the intake water-surface level, find the pressure head just above C and just below C, where C denotes the point of junction. Assume a sudden contraction at C. Use k=0.8 for entrance, 0.24 for sudden contraction and 1.0 for exit. I will downvote the incorrect solution
Three reservoirs A, B and C whose water surface elevations are 60ft, 50ft and 32 ft respectively, are interconnected by a pipe system with a common junction at elevation 35ft. All pipes have a frictional factor of 0.020 and are as described as follows 1. Illustrate the problem 2. What is the direction of flow into reservoir B? 3. Determine the flow from reservoir B in ft^3/s. Indicate if it is Toward or away from junction D. 4. Determine the flow from reservoir C in ft^3/s. Indicate if it is Toward or away from junction D.
Two reservoirs are connected as shown in the figure. The difference in Elevation of the two reservoirs is 6.88m. Darcy-Weisbach friction factor for all pipes, f=0.0238. Pipe 1: Length=3500m Diameter=70cm Pipe 2 and 3: Length=1750m Diameter=35cm Compute the discharge in the pipe one in L/s. Compute the discharge in the pipe three in L/s.
Two pipes are connected in parallel between two reservoirs: L1= 2500 m, D1 = 1.2 m, C1 = 90; L2 = 2300 m, D2 = 0.8m, C2 = 100. For a difference in elevation of 3.8 m, determine the total flow (i.e. total Q) of the water. [Answer in units of m3/s]
Two pipes link two reservoirs (A and B) that are 15m apart in height. Pipe 1 is 60 mm wide and 100 m long. Pipe 2 is 90m long and has a 90mm diameter. Entry loss k = 0.6, exit loss k = 1.0, and f = 0.008 are the same for both. Calculate: 1. How much water flows through each pipe 2. The diameter D of a pipe 100m long that could replace the two pipes and have the same flow.
A pipe system, connecting two reservoirs whose difference in water surface elevation is h= 43 m, consists of 524 m of 830 mm diameter pipe (pipe 1), branching into 687 m of 448 mm diameter pipe (pipe 2) and 697 m of 510 mm diameter pipe (pipe 3) in parallel, which join again to a single 629 mm diameter line 1427 m long (pipe 4). Assuming f= 0.0605 for all pipes, determine the flow rate in pipe 2. Round your answer to 3 decimal places.
P9.) Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P whose elevation is 366 m. reservoir A is at elevation 933 m and reservoir B is at elevation 844 m. the properties of each pipe are as follows: L1= 1500 m, D1= 600 mm, f1= 0.02; L2= 1000 m, D2= 450 mm, f2= 0.025; L3= 900 m, D3= 500 mm, f3= 0.018. A pressure gage at junction Preads 4950 kPa. What is the flow in pipe 3 in m3/s and the elevation of reservoir C. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes
A reservoir A, the free water surface of which is at an elevation of 275 m, supplies water to reservoirs B and C with water surfaces at 180 m and 150 m elevation respectively. From A to junction D there is a common pipe 300 mm diameter and 16 km long. The pipe from D to B is 200 mm diameter and 9.5 km long while that from D to C is 150 mm diameter and 8 km long. Neglect losses other than pipe friction and taking f = 0.01 for all pipes. A. Calculate the rates of ﬂow at A in (m³/s) B. Calculate the rates of ﬂow at B in (m³/s) C. Calculate the rates of ﬂow at C in (m³/s)
A single pipeline x joins pipelines 1,2, and 3 at junction A, and merges again at junction B to form a single pipeline y. Pipelines 1,2, and 3 are parallel to each other. The pressure heads at A and B are 70 m. and 46 m., respectively. Assuming C = 120 for all pipelines, and Pipe 1 length = 3000 m. and diameter = 300 mm, Pipe 2 length = 1300 m. and diameter = 200 mm, and Pipe 3 length = 2600 m. and diameter = 250 mm. Compute the rate of flow at pipeline 1. a. 0.06 m^3/s b. 0.07 m^3/s c. 5.8 m^3/s d. 8.7 m^3/s
Determine the flow in L/s into or out of each reservoir in the pipe system shown; use n=0.011 for all pipes

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS