Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as shown in figure below. Diameter of the pipe is D= 16 cm. (Patm=100 kPa, Ywater-9810 N). Please answer the following questions. (1) E Zmax a) Determine the flow rate of the system. b) Determine the maximum elevation of the highest point of the piping system without causing cavitation (Zmax=?).

Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as shown in figure below. Diameter of the pipe is D= 16 cm. (Patm=100 kPa, Ywater-9810 N). Please answer the following questions. (1) E Zmax a) Determine the flow rate of the system. b) Determine the maximum elevation of the highest point of the piping system without causing cavitation (Zmax=?).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The figure shows a looping water pipe system. Pressure at A = 85 m and E = 55m. Assume f = 0.053 all pipes. a. Compute the discharge at pipe 1b. Compute the discharge at pipe 2c. Compute the discharge at point B
Q3/ The water levels in the two reservoirs A and B are 104.5 m and 100 m respectively above the datum. Pipe joins each to a common point D, where pressure is 98:1 kN/m”*2 gauge at above the joint point D and height is 83-5 m above datum. Another pipe connects D to another tank C. What will be the height of water level in C assuming the same value of ‘f’ for all pipes. Take friction co-efficient f = 0-0075. The diameters of the pipes AD, BD and CD are 300 mm, 450 mm, 600 mm respectively and their lengths are 240 m, 270 m, 300 m respectively. 100 m Your answer
Two water reservoirs of height h1 = 60 m and h2 = 30 m are connected by a pipe that is 0.35 m in diameter. The exit of the pipe is submerged at a distance of 8 m from the (2nd) reservoir surface. a. Provide a diagram b. Determine the flow rate through the pipe if the pipe is 80 m long and the (Fanning) friction factor f' = 0.004. The pipe inlet is set flush with the wall. c. If the relative roughness ε/D = 0.004, determine the friction factor and flow rate.
A pipe AB carries water and tapers uniformly from a diameter of 0.1 m at A to 0.2 m at B over a length of 2 m. Pressure gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 100 kPa) Determine the flow, in m^3/s through the pipe at C neglecting all losses. (1 bar = 100 kPa). (Please round-off final answer to four decimal places) Determine the pressure in bars, recorded at C neglecting all losses. (Please round-off final answer to 2 decimal places)
Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
Two reservoirs whose surface levels differ by 30 meters are connected by a pipe 600mm diameter and 3000m long. The pipe line crosses a ridge whose summit is 9m above the level of and 300m distant from the higher reservoir. Find the minimum depth below the ridge at which the pipe must be laid if the absolute pressure head in the pipe is not to fall below 2.5m of water, and calculate the discharge. Take atmospheric pressure head = 10.3m of water and f= 0.0075
A 1.20 m-diameter(internal)horizontal steel penstock conveys water at the rate of3.6 m3/s. The thickness of the pipe wall is 25 mm. Thebulk modulus of elasticity of water is 2.2 GPa. The pipehas length of 1000 m and the friction factor is 0.020. Thewater surface elevation in the reservoir is 60 m. If theflow is stopped completely by closing the valve in 2sec, determine the following:(a) the maximum water hammer pressure that candevelop.(b) the maximum pressure at the valve.(c) the elongation of the pipe in mm (△=ForcexL/AE) foran almost instantaneous closure.
Q.5. Determine the velocity of the flow out of the vertical pipes at A and B, if water flows into the Tee at 8 m/s and under a pressure of 40 kPa. Assume negligible head loss.
5.10 The water is supplied at the rate of 3 m3 per minute from a height of 4 m to a hydraulic ram, which raises 0.3 m3/minute to a height of 30 m from the ram. The length and diameter of the delivery pipe is 100 m and 70 mm respectively. Determine the D' Aubuisson's efficiency of the hydraulic ram if the co-efficiency of friction f = .009.
The pressures at the ends of 605m long horizontal pipe flow are 350 kPa and 270 kPa. The pressure at the point between the ends is 300 kPa. The pipe is 305mm in diameter and n=0.018. Find the total headloss, amount of flow, and the slope of the egl.
3. (1) Determine an equivalent pipe for the system shown below. (2) If QI = 2.6 cfs, compute (a) the total head loss from A to C, (b) pressure at A if pressure at C is 25 psi, and (c) the flow in each line. Assume that the Hazen-Williams C’s for all pipes are 100 and the pipes are laid on a flat plain.
Determine the pressure (in kN/m2) in the pipe shown (Pressure A) if y=1.24 m, h=1.02 m, and the manometry fluid is mercury (Specific Gravity=13.6).