Q9. a) Design a non-inverting amplifier to have a closed loop gain of 10. The op-amp has an output saturation voltage of 10V, what is its maximum signal amplitude that can be applied to the input without saturation occurring? b) If the output of the op-amp is connected to a load of 5k9, what will be the output current from the op-amp when the maximum voltage is observed at the output of the op. Amp? Note: State any assumptions made in your analysis.

Q9. a) Design a non-inverting amplifier to have a closed loop gain of 10. The op-amp has an output saturation voltage of 10V, what is its maximum signal amplitude that can be applied to the input without saturation occurring? b) If the output of the op-amp is connected to a load of 5k9, what will be the output current from the op-amp when the maximum voltage is observed at the output of the op. Amp? Note: State any assumptions made in your analysis.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

Based on the plots of Vin and Vout, is the op-amp consistent with its inverting function? Justify your answer.
Please answer this two part question A) It is known that when an Op-amp is operated using the negative feedbackconfiguration, the output impedance reduces. Derive an expression that proves this. B) It is known that when an Op-amp is operated using the positive feedbackconfiguration, the output impedance increase. Derive an expression that proves this.
Suppose the op amp shown has an fT of 1 MHz. What is the phase margin of the ampliﬁer?
Assume an inverting amplifier with input resistance 1 kilohm and feedback resistance of 100 kilohm. If the op-amp has GBP = 1 MHz, what is the closed loop amplifier bandwidth?
Why is there a difference between the theoretical and practical values of voltage gain in an inverting and non-inverting Op amplifier?
Suppose that we are designing an amplifier, using an op amp. What problems are associated with using very small feedback resistances? With very large feedback resistances?
Consider an inverting amplifier with a nominal gain of 1000, an op amp with an input offset voltage of 3 mV and an output saturation voltage of plus or minus 10 V. (a) Find the peak value (approximately) of the sine wave input signal that will not cause the output voltage to be cut off? (b) If the effect of Vos is zero at room temperature (25°C): (I) if the circuit operates at a predetermined temperature; (ii) the temperature coefficient of Vas is known to be 10μV/°C, and the circuit is operable In the range of 0°C to 75°C. Please find the maximum signal we can input in the two cases respectively.
For an op-amp having a slew rate SR=5V/ms, what is the maximum closed-loop voltage gain that can be used when the input signal varies by 0.2V in 10ms?
The op amp in the circuit of Figure is ideal.a) What op amp circuit configuration is this?b) Find ?0 in terms of ??.c) Find the range of values for ?? such that ?0 does not saturate and the op ampremains in its linear region of operation.
a) Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kohm resistor in the feedback path, and +-12 v power supplies. b) Using your design from part a, determine the range of input voltages that will keep the op amp in it's linear operating region. c) suppose you wish to amplify a 2 V signal, using your design from part a, with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?
A noninverting ampliﬁer is being designed to have a closed-loop gain of 36 dB. What op-amp gain is required to have the gain error less than 0.15 percent?
Assume for a moment that perfectly accurate resistors were available for feedback networks; that is resistor tolerance is 0%. Then any deviation from the value set by the feedback resistor ratio is caused by insufficient raw op-amp gain. What minimum raw gain would be needed to get within 1% if an intended overall gain of 10? What if the intended gain is 100 instead?