QI/ A balanced three-phase system (4-wires), star-connected generator with ABC sequencehave an internal voltage of 150 with phase angle 0°. The generator feeds a balanced three-phase a Y-connected load having R= 6Q & X= j8N. Find:-a- Draw the circuit in above,b- Phase angle 0, & 03,c- Phase currents of the load,d- Phase voltages,e- Line voltages,f- Draw the phasor diagram,g- Find (Pr,Qr, ST and Fp).

Dear student as per our guidelines we are supposed to solve only one question in which it should…

QI/ A balanced three-phase system (4-wires), star-connccted generator with ABC sequence have an internal voltage of 150 with phase angle 0°. The generator feeds a balanced three- phase a Y-connected load having R= 62 & X- j82. Find:- a- Draw the circuit in above, b- Phase angle 02 & 03, c- Phase currents of the load,

QI/ A balanced three-phase system (4-wires), star-connccted generator with ABC sequence have an internal voltage of 150 with phase angle 0°. The generator feeds a balanced three- phase a Y-connected load having R= 62 & X- j82. Find:- a- Draw the circuit in above, b- Phase angle 02 & 03, c- Phase currents of the load,

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.46P: Three identical impedances Z=3030 are connected in to a balanced three-phase 208-V source by three...

See similar textbooks

Similar questions

A 3- phase star connected load has resistance of 10 Ω, inductance of 15.9mH & a capacitive reactance of 8 Ω respectively in R, B & Y phases. If the voltage between line and neutral line is 231V, 50Hz supply, Assume RYB sequence.Calculate the neutral current and Draw the current & voltage phasors.
A single phase distributor 1 km long supplies a load of 100A at 0.8 p.f. lagging at its far end and a load of 200A at unity p.f. at its mid-point. Both power factors are referred to the voltage at the far end. The resistance and reactance per km (go and return) are 0.1 Ω and 0.2Ω respectively. If the voltage at the far end is maintained at 200V, calculate feeder current, voltage at the sending end . Also find phase angle between voltages at mid-point and sending end.
Three identical impedances Z=3030 are connected in to a balanced three-phase 208-V source by three identical line conductors with impedance ZL=(0.8+j0.6) per line. (a) Calculate the line-to-line voltage at the load terminals. (b) Repeat part (a) when a s-connected capacitor bank with reactance (j60) per phase is connected in parallel with the load.
A single phase distributor 2 kilometers long supplies a load of 120 A at 0·8 p.f. lagging at its far end and a load of 80 A at 0·9 p.f. lagging at its mid-point. Both power factors are referred to the voltage at the far end. The resistance and reactance per km (go and return) are 0·05 Ω and 0·1 Ω respectively. If the voltage at the far end is maintained at 230 V, calculate : • voltage at the sending end • phase angle between voltages at the two ends.
A 3-phase Y-connected source (400V) supplies a 3-phase Y-connected load (3xZload = 27 + 9.0 ohm) via a non-ideal, three-core cable. No neutral line is available. Each conductor of the cable has an impedance Zcable = 80 + 2.1 mOhm a. Measure the phase shift angle between line voltage and phase voltage. b. Because of a fault, one of the three load impedances changes to half its original value. What happens to the phase voltages at the load.
When the three identical star-connected coils are supplied with 400 V, 50 Hz, 3-phase supply, the 1-phase wattmeter whose current coil is connected in line R and pressure coil across the phase Rand neutral reads 6 kW and the ammeter connected in R-phase reads 30 Amp. Assuming RYB phase sequence find: (i) the power factor, of the load, (ii) resistance and reactance of the coil (iii) reactive power of 3-phase load and (iv) Apparent Power Power Factor, of the Load Reactance Resistance Reactive Power Apparent Power
A single-phase circuit is placed across a 120-Vrms, 60-Hz source, with an ammeter, a voltmeter, and awattmeter connected. The instruments indicate 12 A,120 V, and 800W, respectively. Finda. The power factor.b. The phase angle.c. The impedance.d. The resistance.
NOTE: YOU MUST USE THE STANDARD PHASE DIAGRAMTO A THREE-PHASE SYSTEM WITH LINE VOLTAGE OF 230 VAC 60 HZ, A BALANCED LOAD OF 9+j6 Ω IS CONNECTED.IF THE LOAD IS CONNECTED IN DELTA, DETERMINE:A) THE MAGNITUDE OF THE CURRENT OF Ia.B) THE ANGLE OF THE LINE CURRENT Ia.C) THE THREE-PHASE POWER CONSUMEDD) THE VALUE OF EACH CAPACITOR (IN μF) OF THE STAR-CONNECTED CAPACITOR BANK, TO CORRECT THE PF TO ONE.
When the three identical star-connected coils are supplied with 415 V, 50 Hz, 3- p supply, the 1- p wattmeter whose current coil is connected in line R and pressure coil across the phase R and neutral reads 12 kW and the ammeter connected in R-phase reads 26 Amp. Assuming RYB phase sequence find: (i) the power factor, of the load , (ii) resistance and reactance of the coil (iii) reactive power of 3- p load and (iv) Apparent Power
31. A 3-phase 3-wire star-connected load consists of a capacitive reactance of 100ohm in the red phase and a resistor of 100ohm in Bo- each of the other phases. The line voltage is 440 V and the phase sequence is RYB. If the power is measured by the 2-wattmeter method,the current coils being connected in the red and yellow leads respectively, determine the reading of each instrument. (-86.5 W, 1.640 W) Answer
A 3-phase, 50 Hz, overhead transmission line delivers 10 MW at 0·8 p.f. lagging and at 66 The resistance and inductive reactance of the line per phase are 10 W and 20 W respectively while capacitance admittance is 4 × 10- 4 siemen. Calculate : (i)the sending end current (ii) sending end voltage (line-to-line) (iii) sending end power factor (iv) transmission efficiency Use nominal T method.
The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/ km. At the end of the line, a 70 MVA star connected load with a power factor of 0.8 back under 69 kV interphase voltage is fed. Capacitive circuit element with a capacitance of 19.14 mikro F / phase is placed as shunt at the end of the transmission line. According to these given; a) Line head voltage and current, b) Calculate the active and reactive power per line.