QI. In the circuit shown in Fig. Ql. v(t) = 56e 200 V, t>0 i(t) = 8e 2001 mA, t>0 (a) (b) (c) Find the values of R and C. Calculate the time constant t. Determine the time required for the voltage to decay half its initial value at t = 0. Fig. Q1 ww

QI. In the circuit shown in Fig. Ql. v(t) = 56e 200 V, t>0 i(t) = 8e 2001 mA, t>0 (a) (b) (c) Find the values of R and C. Calculate the time constant t. Determine the time required for the voltage to decay half its initial value at t = 0. Fig. Q1 ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A team of electrical engineers wants a new smart phone’s battery to last for 12 hours. If the smart phone has an average appliance load of 2.6 watts, what does the battery capacity need to be, in amp hours? Express your answer as a decimal to the nearest hundredth. 5.2 The charging time t, in hours, of a phone with battery capacity c, in amp hours, can be calculated using the equation t = 2c. If Jared’s new phone has a battery capacity of 3.72 Ah, how many hours will it take his phone to fully charge? Express your answer as a decimal to the nearest tenth. 5.3 Marnie buys a smart phone from a different company. She heard that this phone takes only 4 hours to charge. Assuming Marnie’s smart phone has an average appliance load of 2.6 watts, how many hours can Marnie expect to use her phone before the battery dies? Express your answer as a decimal to the nearest tenth.
At time = 0, a constant heating power of 100 kW is applied to a boiler that intends to raise the temperature of the fluid inside to 100 ºC. The initial temperature of the fluid is 25 ºC. Temperature is taken every 2 minutes, starting at t = 0. The log after 1 hour is shown below. The x-axis is time (in minutes) while the y-axis is the temperature T. The system may be assumed to be of first order. Let θ(t) be the function describing the temperature increase, i.e. θ(t) = T(t) - 25, where T is the actual temperature. The input power is p(t) = 100 u(t) kW. 1. What is a feasible time delay, in minutes, for the system? 2. What is the DC gain of the system O(s)/P(s) in Cº/kW? 3. What is the transfer function O(s)/P(s)
An industrial plant is supplied by a power utility company with voltage of 7.97 kV. To monitor the plant’s performance and consumption, the utility company installed a potential transformer (PT) and a current transformer (CT) at the plant’s premises. The specs of the transformers are as shown on Fig. 1. If V , negative sequence (that is V, V) , and plant is drawing 2000 kW at 0.90 pf lagging, find the following:1.Assuming the load is Y-connected, what is the voltage VAN in volts? Enter magnitude only in 2 decimal place.
A RL network supplied with 10V battery Find the mathematical expressions for the transient behaviour of vl, iL, VR2 and VR2 when the switched is moved to position 2. Sketch the curves of vL, iL and VR2. Then find How much time must pass before it can be assumed, for all practical purposes, that iL =0A and vL = 0 Volt? PLEASE STEP-BY-STEP STEPI NEED THEM TO STUDY.
A 500-liter tank initially contains 10 grams of salt dissolved in 200 liters of water. Starting at t=0, water that contains 1/4 grams of salt per liter is poured into the tank at the rate of 4 liters/min, and the mixture is drained from the tank at the rate of 2 liters/min. Let y(t) represent the amount of salt inside the tank at time t. Find a differential model for y(t) and solve it to find y(t). Graph y(t). What is the amount of salt after 10 minutes? What is the concentration of salt inside the tank after 10 minutes?
A RL network supplied with 10V battery (a)Find the mathematical expressions for the transient behaviour of vL, iL , vR2 and vR2 when the switched is moved to position 2. Sketch the curves of vL, iL and vR2.A how much time must pass before it can be assumed, for all practical purposes, that iL=0A and vL = 0 Volt?
Heat capacity Cv is the amount of heat required to raise the temperature of a given mass of gas with constant volume by 1 °c, measured in units of cal / deg-mol ( calories per degree gram molecular weight). The heat capacity of oxygen depends on its temperature T and satisfies the formulaCv = 8.27 + 10^-5 (26T - 1.87 T^2) Use Simpson's Rule to find the average value of Cv and the temperature at which it is attained for 20°c less or equal to T less or equal to 675°C.
1. An electrical circuit consist of a series connected resistor (100 ohms) and a coil with inductance of 50 H. If the initial DC source is 200 volts, solve for the current at 2 seconds. 2. A population of a small city had 3000 people in the year 2000 and has grown at a rate proportional to its size. In the year 2005 the population was 3700. Estimate the population of the city in 2006 and in 2010.
1 - A square chip, with side ? = 5 mm, operates under isothermal conditions.The chip is positioned on a substrate so that its side and bottom surfaces are thermally insulated, while its top surface is exposed to theflow of a refrigerant at ?∞ = 15°C. From reliability considerations, the chip temperature cannot exceed ? = 85°C. The refrigerant being air, with a convection heat transfer coefficientcorresponding ℎ = 200 W/(m2K), what is the maximum allowable power for the chip? Since the coolant is a dielectric liquid for which ℎ = 3000 W/(m2K), what is the maximum allowed power?
The transformer in the circuit shown in Fig. 1(a) is an ideal transformer with a=1/3. The circuit is supplied from a sinusoidal ac source with a frequency 60 Hz. Determine the angular speed ω. Determine the source voltage RMS value. Express the supply voltage as a function of time. Calculate the load resistance value (9 Ω) referred to the transformer low voltage side. Calculate the circuit equivalent resistance as seen by the source. Calculate the current drawn from the supply. Calculate the load voltage Vo. Calculate the power dissipated in the 3 Ω resistor. Draw, to scale, the phasor diagram including: supply voltage, supply current, load voltage and load current.
The numerical values for the voltages and the currents in the circuit of Fig.P1.9 are given in the Table P1.9. Find the total power developed in the circuit.
Suppose an electrical signal generated, y(t) can be modelled as follows where t, is time in second, y(t) is voltage in mv. a) Produce graphs showing the amplitude and phase spectrum of y(t). b) State whether this time-domain signal y(t) is periodical, or non-periodical and justify your answer.