Que.5 A long natural slope in overconsolidated fissured clay of saturated unit weight 22kN/m³, is inclined at 14 degrees to the horizontal. The water table is at the surface and seepage is approximately parallel to the slope. A slip surface has developed on a plane parallel to the surface at a depth of 4m. Determine the factor of safety along the slip plane using the residual strenght parameter, 'r=20 degrees.

Que.5 A long natural slope in overconsolidated fissured clay of saturated unit weight 22kN/m³, is inclined at 14 degrees to the horizontal. The water table is at the surface and seepage is approximately parallel to the slope. A slip surface has developed on a plane parallel to the surface at a depth of 4m. Determine the factor of safety along the slip plane using the residual strenght parameter, 'r=20 degrees.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.17P

See similar textbooks

Similar questions

A long natural slope in an over-consolidated clay (c'=10kPa, φ'=25deg, γsat=20kN/m3) is inclined at 10 degrees to the horizontal. The water table is at the surface and the seepage is parallel to the slope. If a plane slip had developed at a depth of 5m below the surface, determine the factor of safety. Use γwater=10kN/m3.
Explain about the Noncircular slippage plane for slope stability analysis, Janbu method.
Civil engineering:(a) Calculate the thing of protection of the block against sliding if the density of the rock is 23.5kN / (m ^ five) . (b) Is the block solid against toppling as described by way of the relation: Ax/y tan V-solid? (c) How much greater undercutting of the fault need to occur earlier than toppling failure takes place ? d) What stabilization measures might beappropriate for this slope?
plz, solve this problem and follow the instructions. Geotechnical Engineering-2 Question-4:(a) The slope of a water-retaining embankment is 1 vertical, 2 horizontal and the vertical height is 10 m. The soil is fully saturated and has an undrained cohesion of 29 kPa and a unit weight of 20 KN/m3. Determine the factor of safety against shear failure along the trial circle shown in Fig. 1, when the water level is at the top of the embankment as shown in figure 1. Hint: (Area of slip mass is 184 m2)
What is the factor of safety of a slope behind a geomembrane-lined pond when it is empty if the soil fails under undrained conditions? The slope is 3H to 1V, 7.5-meters deep, and will be of the toe failure type (i.e., n = 1.0). The soil’s unconfined compressive strength is qu = 35 kN/m2 (note that qu = 2c) and its unit weight is 18 kN/m3. Show your work! **HINT: you will need to reference the figure below for your Ns value for “soils whose strength can be approximated by undrained conditions”.
A site consists of a 12 m thick saturated clay deposit underlain by bedrock. The clay has ??=20.0????/??3and ????=40????/??2 . If an excavation is to be made at a slope angle ??=25° to a depth of 10.0 m, what would be the factor of safety FSs? What type of failure circle would you expect?
. A triangular fill with dimensions as shown below is piled on the slope. The shear strength parameters of the plane between the fill material and the slope were determined as 12 kPa and 25°. Since the unit weight of the fill is 18.5 kN/m3, calculate the factor of safety against sliding.
A cut slope is to made. The unit weight of soil is 17 kN/m^3 and the angle of internal friction is 20°. The soil has a cohesion of 24 kPa. The cut slope makes an angle of 30° with the horizontal and the height is 9 m. if the trial failure plane is 15°from the horizontal. Determine the following: 1. Frictional force along the failure plane. 2. Cohesive force along the failure plane. 3. Factor of safety against sliding.
An embankment for road traffic is required to be constructed with the followingdimensions :Top width = 8 m, height = 4 m, side slopes= I V : 1.5 HorThe unit weight of soil under the worst condition is 21 kN/m3. The surcharge load on theroad surface may be taken as 50 kN/m2. Compute the vertical pressure at a depth of 6 mbelow the ground surface at the following locations:(i) On the central longitudinal plane of the embankment,(ii) Below the toes of the embankm
An infinite slope in purely cohesive soil has a saturated unit weight of 20 kN/m^3 and effective cohesion of 48 kPa. It has a slope of 18 degree. The clay has a depth of 5m over ledge rock. Depth of clay is measured vertically. 1. Determine the FS against slippage. 2. Determine the critical depth. 3. Compute for the stability number.
A long slope is formed in a soil with shear strength parameters: c’ = 0 and ϕ’ = 34⁰. A firm stratum lies below the slope and it is assumed that the water table may occasionally rise to the surface, with seepage taking place parallel to the slope. Use ϒsat = 18 kN/m3 and ϒw = 10 kN/m3. The maximum slope angle (in degrees) to ensure a factor of safety of 1.5, assuming a potential failure surface parallel to the slope, would be most nearly equal to?
A cut slope was excavated in a saturated clay. The slope made an angle of 39.55 degree with the horizontal. Slope failure occurred when the cut reached a depth of 6 m. Previous soil explorations showed that a rock layer was located at a depth of 10 m below the ground surface. Assuming an undrained condition and γsat = 18 kN/m3, Analyze the following. a. undrained cohesion of the clay.b. nature of the critical circle?c. With reference to the toe of the slope, at what distance did the surface of sliding intersect the bottom of the excavation?