QUESTION 02 Figure Q2(a) shows a stainless-steel beam ABC with a uniformly distributed load along ABC. The beam is pin supported at point A and B. The Modulus of Elasticity, E of this beam is 200 GPa. (a) Draw the shear force and bending moment diagrams for the beam and indicate all important points on the diagrams. (b) If the cross-section of the beam is as shown in Figure Q2(b), determine the maximum bending stress at points P and Q and identify its type (compression or tension). (c) Calculate the maximum transverse shear stress at point R (joint between the flange and the web). (d) Without calculation, what effect does it have on the transverse shear and bending stresses calculated above if a material of a lower value of Modulus of Elasticity is being used. State the reason for your answer.

QUESTION 02 Figure Q2(a) shows a stainless-steel beam ABC with a uniformly distributed load along ABC. The beam is pin supported at point A and B. The Modulus of Elasticity, E of this beam is 200 GPa. (a) Draw the shear force and bending moment diagrams for the beam and indicate all important points on the diagrams. (b) If the cross-section of the beam is as shown in Figure Q2(b), determine the maximum bending stress at points P and Q and identify its type (compression or tension). (c) Calculate the maximum transverse shear stress at point R (joint between the flange and the web). (d) Without calculation, what effect does it have on the transverse shear and bending stresses calculated above if a material of a lower value of Modulus of Elasticity is being used. State the reason for your answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of the 5-kip load. Follow the sign convention. a) Determine the normal force at point E. Express your answer in kilopounds to three significant figures. b) Determine the shear force at point E. Express your answer in kilopounds to three significant figures. c) Determine the moment at point E. Express your answer in kilopound-feet to three significant figures.
Calculate uniform load frame reactions, and normal force, shear force and bending moment and draw diagrams. L= 6m H= 4m F1= -10kN F2= -6 Kn P= 3kN/m
Beam ABCD carries a concentrated load and uniformly distributed load as shown below. Draw the shear and moment diagram of the given beam. Show your solution.
Derive the singularity equation of moment for the beam shown in figure I then:- 1- Draw bending moment diagram for the beam (by using the singularity- Macaulay's equation) 2- Determine the maximum bending stress in the section (square section with side length of 40cm)
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa, calculate: Using a T-beam geometry, determine the required amount of flexure bars for maximum ultimate bending. = [As] sq.mm (whole number)
Based on the following figure determine the vertical reaction at the hinge type support for the loads shown on the beam. Consider that the dimensions are in meters. For the exercise use a value of x equal to 7.3 m, a value for the distributed load w equal to 160 N/m and a value for the force F equal to 532 N.
For the beam shown below, given that AB = 5 m, AC = 1 m, and P = 5 kN, draw the FBD, shear & momment diagram, and then calculate the magnitude of the internal bending moment at cross-section C of the beam: ____ kN m. Calculate your solution to 1 decimal place.
a) For the image above, find the shear force and bending moment diagram. Show calcs for all your work. Assume a distance A of 1.5 m, a point load P = 40 kN, and a distributed load w of 5 kN/m. Enter the maximum positive moment b) If the beam has an moment of inertia, Ix = 400 x 106 mm4 , and the total distance between the top and bottom edges of the beam is 320mm, determine the maximum compressive stress that occurs at the bottom edge of the beam. Assume the centroid is in the middle of the beam (ctop =cbot)
ASAP PLEASE. 4 DECIMALS THANK YOU a. Determine the maximum positive shear force in kN. b. Determine the maximum negative shear force in kN. c. Determine the maximum positive bending moment in kN-m. d. Determine the maximum negative bending moment in kN-m. e. Determine the point of inflection from point C in meters.
PLEASE ANSWER ASAP TY! A 2-m long cantilever beam carries a uniformly distributed load of 10KN/m over its entire length. The beam has a rectangular cross-section with dimensions 200 mm wide and 400mm high. a) Determine the maximum flexure stress in the beam (in MPa). b) Determine the moment of inertia about the neutral axis of the cross-section (in mm4) c) Determine the magnitude of bending moment at a section 0.5m from fixed support (in KN-m). d) Determine the absolute maximum bending moment along the length of the beam (in KN-m).
Q2. A heavy storage warehouse building is made of 200 mm thick stone concrete floor. The floor slab having a length of 9 m and width of 4 m is directly over the top of the simply supported beam as shown in Figure Q2 as in APPENDIX II. The beam is made from reinforcement concrete with the size 250 mm x 300 mm. The combination of dead load and live load will be provided with the resultant force, P at point C. The beam is supported with roller support at both ends A and B. Given the value of elastic modulus, E = 200 kN/mm2. Evaluate the slope and deflection at point D using the Macaulay method. (the resultant force, P not provided)