Question 1 A weight of 50 N is allowed to fall freely through a height of 130 mm onto a rigid stop attached to the lower end of a vertical steel rod 450 mm long. The rod has a diameter of 12 mm for a length of 250 mm and a diameter of 8 mm for the remaining 200 mm. (E = 207 GPa). 1.1 Calculate the maximum stress induced in the rod. 12 mm 250 mm 450 mm 50 N 130 mm 8 mm

Question 1 A weight of 50 N is allowed to fall freely through a height of 130 mm onto a rigid stop attached to the lower end of a vertical steel rod 450 mm long. The rod has a diameter of 12 mm for a length of 250 mm and a diameter of 8 mm for the remaining 200 mm. (E = 207 GPa). 1.1 Calculate the maximum stress induced in the rod. 12 mm 250 mm 450 mm 50 N 130 mm 8 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.55P: Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free...

See similar textbooks

Similar questions

An object weighing 40 N is drop from a height of 4 m and hits a vertical steel rod on top. Determine the stress of the rod. Diameter 4 mm, length 4 m. Neglecting buckling.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
Two springs, as shown are to carry a load of 90 kN. The spring on the left is the larger spring. Spring specifications are as follows: wire diameter=25 mm, outside coil diameter= 230mm, no. of active coils=8; and wire diameter=20 mm, outside coil diameter= 170mm, no. of active coils=20. Take G= 79 GPa. Determine the force exerted by each spring and the stress induced in each.
1. A cylinder tankhas a maximum load of 2600 kg while the pressure is 2600 kpa. If the ultimate stress is 55 000 kpa and a factor of safety is 4.5, calculate the required wall thickness of the cylinder. Choose the correct answer below and show complete solution: a. 18.34 mm b. 14.38 mm c. 13.48 mm d. NOTC 2. A spherical tank has a diameter of 12 m, if the tangential stress of the tank is 18 Mpa, determine the maximum internal pressure of the tank can carry if the wall thickness is 25 cm. Choose the correct answer below and show complete solution: a. 150 kPa b. 15000 kPa c. 1500 kPa d. NOTC 3. A cylindrical tank has an inside diameter of 6-in and is subjected to an internal pressure of 600 psi. If the maximum stress is 1300 psi, calculate the required thickness. Choose the correct answer below and show complete solution: a. 0.1385 in. b. 0.3185 c. 0.8135 d. NOTC
A thin copper tube, 14 mm internal diameter and 0,5 mm wall thickness has closed ends and rotates at 1200 r/min while it is subjected to an internal gauge pressure of 222 Pa. Calculate the total hoop stress in the wall of the tube if the density of copper is 8900 kg/m3.
The outside diameter of the coils of a safety valve spring is 120 mm while its wire diameter is 15 mm. This spring, having 10 active coils has the ends in plain ground, and has a free length of 200 mm. 1. Determine the length (in mm) at which this spring must be initially compressed to hold a pressure of 1400 kPa applied on a 32-mm diameter valve seat. Use a modulus of rigidity of 80 GPa. 2. calculate the spring’s maximum stress induced if it is compressed to its solid length
Compute the minimum vine diameter to provide a desired factor of safety of 1.7 against yield-type failure. Assume a yield stress of 300 MPa, and that the mass of the monkey is 65 kg. Hint Weight (N) = Mass (Kg) X g (9.81 m/s2)
A load P is supported by two springs arranged in series. The upper spring has 20 turns of 29-mm diameter wire on a mean diameter of 150 mm. The lower spring consist of 15 turns of 10-mm diameter wire on a mean diameter of 130 mm. Determine the value of P that will cause a total deflection of 80 mm. Assume G = 80 GPa for both spring.
A closely coiled helical spring is to carry a load of 500N. Its mean coil diameter is to be 10 times that of the wire diameter. Calculate these diameters if the maximum shear stress in the material of the string is to be BOMN/m*2.
A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and trunk onto a steel will 800.50 mm in diameter. The modulus of elasticity of steel is 200 GPa. 1) Which of the following most nearly gives the tensile stress in the tire. a. 145 MPa b. 130 MPa c. 110 MPa d. 125 MPa 2) Which of the following most nearly gives the compressive pressure between the tire and the wheel. a.) 4.35 MPa b.) 3.30 MPa c.) 3.90 MPa d.) 3.75 MPa 3) If the tire has an allowable tensile stress of 124 MPa and is to resist a pressure of 1.50 MPa, which of the following most nearly gives its thickness. a.) 4.84 mm b.) 2.42 mm c.) 2.58 mm d.) 5. 16 mm
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
Question 4A close-coiled helical spring is to have a stiffness of 90 kN/m and is to exert a maximum force of 3.7 kN. If the mean diameter of the coils is 80 mm, and the maximum stress is not to exceed 300 MPa, calculate the required number of coils and the diameter of the steel rod from which the spring should be made (G=80 GPa).