Question 1 Determine (approximately) the force in members GF, GJ and GK of the steel portal frame as shown in Figure Q1. Also, find the reactions at the fixed column supports A and B. Assume all members of the truss to be pin connected at their ends. The frame is subjected to a 45 kN and 50 kN horizontal load at point H and I, respectively. Use portal method. 45 kN 50 KN F K 4m @4 = 16 m E Figure Q1: Steel Portal Frame D. B 3 m 1.5 m 6 m

Question 1 Determine (approximately) the force in members GF, GJ and GK of the steel portal frame as shown in Figure Q1. Also, find the reactions at the fixed column supports A and B. Assume all members of the truss to be pin connected at their ends. The frame is subjected to a 45 kN and 50 kN horizontal load at point H and I, respectively. Use portal method. 45 kN 50 KN F K 4m @4 = 16 m E Figure Q1: Steel Portal Frame D. B 3 m 1.5 m 6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The frame has dimensions H1 = 4 m , H2 = 3 m , and L1 = 6 m , and supports two lateral loads P1 = 10 kN and P2 = 12 kN . The area of column AE is 40 cm2 and the area of column BF is 80 cm2 . Gy = 13.3 kN Ax = 11.0 kN a) What is the horizontal reaction from the ground on the base of the column at B? Let a positive reaction be pointing to the left. Bx = ?
Determine the reaction at the roller support and draw the bending moment diagram for the beam and loading shown. E=200 GPa, I=85*(10)^-6 m^4 P=120 kN, W=60 kN/m
The given structure was supported by pin supports at points D and E. Member EF, DFG and BGC are connectedto each other by internal hinges at B and F and a slider at G. (The slider at G allows relative horizontal motionsof members BGC and DFG but constrains the vertical movement of members BGC and DFG. Calculate thesupport reactions due to pin supports and all internal hinge reactions. Show your calculation steps in detailand write your answers in the box below.
QUESTION 2. For the beam under the shown loading: a) Determine the reactions at the supports (20 p) b) Determine the internal normal force, shear force, and the bending moment at points B and C (20p).
The steel rod is fixed to the side at ‘A’, and before it is loaded, there is a gap of 0.15-mm between the side at ‘D’ and the other end of the rod at ‘C’ as shown in the figure below. Determine the support reactions at ‘A’ and ‘D’ if the rod is subjected to an axial force, ? = 200-??. Take ??? = 200-???.
FROM THE FIGURE 1. Which of the following most nearly gives the moment reaction at the fixed support? a. 35 kN-m b. 45 kN-m c. 70 kN-m d. 82 kN-m 2. Which of the following most nearly gives the maximum shear? a. 25 kN b. 50 kN c. 40 kN d. 60 kN 3. Which of the following most nearly gives the maximum positive bending moment? a. 8.25 kN-m b. 10.12 kN-m c. 13.3 kN-m d. 15.45 kN-m
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
Is the another support force possible solve like this: r3*9m-4KN/m*2.5m*6.5m-12KN*1m=0 >r3= 8.56 KN
For the beam shown in the figure: 1. Which of the following most nearly gives the moment reaction at the fixed support? a. 35 kN-m b. 45 kN-m c. 70 kN-m d. 82 kN-m 2. Which of the following most nearly gives the maximum shear? a. 25 kN b. 50 kN c. 40 kN d. 60 kN 3. Which of the following most nearly gives the maximum positive bending moment? a. 8.25 kN-m b. 10.12 kN-m c. 13.3 kN-m d. 15.45 kN-m
The frame shown below is pinned at joints A and F. The frame consists of three rigidmembers; ACB, BDF, and ACE, connected by pin joints at C, B, and D. The frame is loaded at Ewith a downward force of 1000 N. Lengths AC = CB = 2.7 m, length AF = 4.8 m, and length DE =1.2 m. Determine the magnitude of the vertical component of the reaction force at pin B (N).
For the beam shown, determine the reaction at the roller support when w0 = 6 kips/ft.
In the shown loaded truss, P = 225 kN, calculate the following and select the correct values from the given drop-down list: a) the support reactions at roller A and pin B (i.e., Ax, Ay & By ). 3 m b) the angle a. c) the forces in members AC and AB using the method of joints (i.e., FAC & FAB).