Four wheel loads rolls as a unit across a 19-m span. The loads are 40 kN, 40 kN, 30 kN, and 10 kN separatedrespectively by distances of 2 m, 3 m and 6 m. Compute the maximum shear in kN. twó decimal places, e.g. 50.00, to have full credit.O to include the unit of your answer.O NOT COPY the answer of your classmates since the exam that was prepared for you generates 200 sets,ISTINCT problem to solve.ck and God Bless.Question 1Four wheel loads rolls as a unit across19-m span.respectively by distances ef 2 m, 3 m and 6 m. Compute the maximum shear in kN.loads are 40KN. 40 kN, 30 kN, and 10 kN separatedNextNo new data to save. Last checked at 2:12pmSubmit

Answered: Image /qna-images/answer/cf0d3ec1-e04e-4400-9b93-ecd9bb501a95.jpg

Answered: Question 1 Four wheel loads rolls as a…

Question 1 Four wheel loads rolls as a unit across a 19-m span. The loads are 40 kN. 40 kN, 30 kN, and 10 kN separated respectively by distances of 2 m, 3 m and 6 m. Compute the maximum shear in kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Can someone please solve this? Find load function functions and draw load effect diagrams? Fx=4.5KN.Fz=2.5 KNMB = 2.5 KNm.a= 1.6M.
In the articulated belt system given in the figure,At point C, before 60N single load, sectionfind its effects
Complete Solution. Thank you! I'll rate asap. Given: a = 23.5 kN, b = 22.5 kN, c = 4.5 m Instructions: 3 Decimal Places Questions: a. Using Cantilever method, calculate for the force in kN at member DC. b. Using cantilever method, calculate for the axial force in kN at member CB. c. Using cantilever method, calculate for the axial force in kN at member FE. d. Using cantilever method, calculate for the axial force in kN at member CG. e. Using cantilever method, calculate for the axial force in kN at member GK.
PLEASE ANSWER ALL THE QUESTIONS BELOW. SHOW COMPLETE SOLUTION AND ANSWER ACCURATELY. REFER TO THE GIVEN VALUES IN THE FIGURE. I WILL GIVE A DOWN VOTE TO WRONG ANSWER. I WILL RATE ASAP. THANK YOU! The indeterminate continuous beam below is loaded with gravity loads as shown. Using MOMENT DISTRIBUTION METHOD, compute for the following due to applied loads. Show complete solution from the computation of distribution factor, fixed end moments, balancing, unbalanced moments, and total joint moment for each member. Use up to Bal5. - Distribution Factor at joint C of member CB. DFCB - Fixed end moment at joint C of member CD in kN-m. Indicate negative sign if counter-clockwise. FEMCD - Moment at support A in kN-m. Indicate negative sign if counter-clockwise. MA - Moment at joint D of member DC in kN-m. Indicate negative sign if counter-clockwise. MDC - Vertical support reaction Rb in kN. Indicate negative sign if downward. Rb
NEED HELP ASAP PLEASE!!! A horizontal shelf AD of length L = 740 mm, width b = 360 mm, and thickness t = 30 mm is supported by brackets at B and C [see part (a) of the figure]. The brackets are adjustable and may be placed in any desired positions between the ends of the shelf. A uniform load of intensity q. which includes the weight of the shelf itself, acts on the shelf [see part (b) of the figure]. A L (a) D L (b) Determine the maximum permissible value of the load if the allowable bending stress in the shelf is Oallow = 7.5 MPa and the position of the supports is adjusted for maximum load-carrying capacity. Round to two decimal places. qmax kN/m
Two 10° wedges of negligible weight are used to move and position the 400-lb block. Knowing that the coefficient of static friction is 0.25 at all surfaces of contact, determine the smallest force P that should be applied as shown to one of the wedges.
the weight of the file cabinet is 60 lbs and G represents its center of gravity the coeffiecent of friction between the cabinet and the floor is 0.3 determine the minimum horizontal force P required to cause the cabinet to..... a) slide across the floor b) to tip over c) if the force p equals 12 what happens?
Analyze the given semi-frame and Develop the required equation/solution for every given answer. 1. What is the shear at E? 2. What is the shear and moment at point C? 3. What is the shear and moment at point A? please provide a solution, thank u so much.Given: Shear and moment at left of C Vc= -4.5 kn Mc= -4.5 kn-m Shear and moment at right of C Vc= 37.5 knMc= -94.5 kn-m
Given: a circular 1.5 in. diameter solid steel column carrying a compressive load with pinned ends. The length is 72 in. Use E = 29,000 ksi for the steel rod. Calculate the critical load for column buckling:___ kip.
For the beam and loading shown, determine the vertical reaction at A (lb) provided that a=152, b=113, c=7 and d=3. Round off only on the final answer expressed in 3 decimal places.
Calculate the member force on member HF in Kips? Specify if T or C. 87.6 C 105.9 C 79.7 C 97.5 C 112.1 C
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS Determine the shear force 6.34 ft to the right of point A for the beam shown below if P = 1026 lb, W = 362 lb/ft, T = 4311 lb ft, a = 3.15 ft and b =5.68 ft. Round of the final answer (in lb) to four decimal places.