Question 1 The pressure tank shown has a 8-mm wall thickness and butt-welded seams forming an angle ß = 20° with a transverse plane. Determine the largest allowable gage pressure, knowing that the allowable normal stress perpendicular to the weld is 120 MPa and the allowable shearing stress parallel to the weld is 80 MPa. .3 m² 1.6 m

Question 1 The pressure tank shown has a 8-mm wall thickness and butt-welded seams forming an angle ß = 20° with a transverse plane. Determine the largest allowable gage pressure, knowing that the allowable normal stress perpendicular to the weld is 120 MPa and the allowable shearing stress parallel to the weld is 80 MPa. .3 m² 1.6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cylindrical portion of the compressed air tank shown is fabricated of 0.25-in.-thick plate welded along a helix forming an angle β= 30° with the horizontal. Knowing that the allowable stress normal to the weld is 10.5 ksi, determine the largest gage pressure that can be used in the tank
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 26 ksi.
Calculate the maximum stress in a 5mm thick steel plate with an 18 mm diameter round hole, given h gross = 12cm and the tensile load is 8.5 kN. (Submit answer in Mpa) Please solve carefully, Specifically Area calculation. Thanks
Six 20-mm-diameter rivets fasten the plate to the fixed member. Determine the shearing stress caused in each rivet by the 40kN loads. What additional load P can be applied before the average shearing stress in any rivet exceeds 60MPa?
A threaded steel rod (Es = 210 GPa, dr = 12 mm, αs = 12 x 10-6/˚C) is held stress free between rigid walls by a clevis and pin (dp = 15 mm) assembly at each end. If the allowable shear stress in the pin is 45 MPa and the allowable normal stress in the rod is 70 MPa, what will be the maximum permissible temperature drop ΔT?
The outer diameter of the bronze pipe flush-mounted at the A and B points is given as D and the wall thickness as s. The pipe is tightened at the C point with a pipe wrench. Determine the greatest torsional stress that will occur in the pipe.D=11mm y=3mm F=140N
The elliptical pipe carrying steam at 3.5 mPa has an outer major axis length of 500 mm and an outer minor axis length of 400 mm with a wall thickness of 10 mm. A gasket is inserted between the flange at end of the pipe , and a flat plate is attached using 40 mm diameter bolts to cap the end . The allowable Stress in the bolts is 80 Mpa. How many bolts must be used to hold the cap if there is an initial stress of 30 mPa ?
The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 700 mm and a wall thickness of 9.5 mm. For a gage pressure of 0.83 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume β=32∘
Compute the stress at each segment of the pipe.
the rectangular beam having a dimension of b= 320mm, h=460mm with 4pcs-28mm diameter reinforcing bars, determine the following a) cracking moment if fr =3.4MPa, b) stressed if moment (M)=42kN-m and n=9
The plate shown is fastened to the fixed member by seven 12-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 75 MPa. If P = 8000 N, what is the minimum shearing stress developed in the rivet.
What is the minimum required bolt diameter (mm) at C ifthe allowable bolt shear stress is 68 Mpa.a. 9 mm c. 11 mmb. 10 mm d. 12 mm Determine the stress (Mpa) in strut BC.a. 5.6 MPa c. 3.2 MPab. 2.8 MPa d. 6.4 MPa Calculate the bolt stress (Mpa) at A if its diameter is 20mm.a. 7.64 MPa c.11.46 MPab. 3.82 MPa d.14.92 MPa