Need ot very fast i will give multiple upvotes Question CompletionQUESTION 11A student decides to construct a capacitor using two circular conducting plates with diameter 16 cm. She separates the plates with a paper dielectric (e, - 2that is thick 0.5 mm. What is the capacitance of her capacitor?0.850 p3.56 nF100.53 F890.1 p

Given: Diameter, d0=16cm Thickness, d= 0.5mm=5×10-4m ∈r=2

Answered: QUESTION 11 A student decides to…

QUESTION 11 A student decides to construct a capacitor using two cular conducting plates with diameter 16 cm. She separates the plates with a paper dielectric (e, 890.1 p

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 3RQ: A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted...

See similar textbooks

Related questions

Q: A 4-pole alternator, on open-circuit, generates 200 V at 50 Hz when the field current is 4 A.…

Q: hat is the value of V in

A: Given data, Circuit diagram is given as,

Q: Using the Laplace transform, calculate the convolution y(t) = x(t)∗h(t) of the pair of signals.

A: In this question We need to determine the output of the given signal. We are solving this problem…

Q: TOPIC: COMBINATIONAL CIRCUIT What is a half-adder? Write its truth table. Design a half-adder using…

A: Since you have posted the multiple questions so we are supposed to answer 3 questions only. In the…

Q: Four resistors and an ideal (zero resistance) battery are laid out in a star-shaped pattern, and…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 2.43 Apply voltage and current division to determine Vo in the circuit of Fig. P2.43 given that…

A: Given data The output voltage across the resistor of 1 Ω is Vout=0.2 V. We have to find out the…

Q: Fill in the Blanks: Q: If an input signal is bounded, then the output signal must also be bounded,…

A: System has many properties like Causality Stability Lineraity Time dependency, etc

Q: Q1/ Answer by True or False and correct the false sentence: 1- Wire.begin() is used to initiate the…

A: here is answer of each sentence and correction f those which are false

Q: v(t) = 320 cor (3 i (t) = 10 sin (377€ -3°) +30.) Find the load impedance b) The complex paver…

Q: determine the cross-sectional area

Q: Use the node-voltage method to find v0 in the circuit attached.

A: In this question We need to determine the value of voltage Vo as shown the circuit. We are solving…

Q: Determine the power supplied by the 36-V source in the circuit.

A: To determine the power supplied by 36 V source

Q: 150 Ω 13 3800 V 12 Μ 80 Ω 1

Q: A typical ceiling fan on medium speed rotates at a frequency of 150 rpm (revolutions per minute).…

A: The given value of speed of a typical ceiling fan at a frequency is Nr=150 rpm. We need to determine…

Q: Find v (t) for t >0 in the circuit below and plot the response including the time interval just…

Q: In reference to Figure 2, given the dc load line and the transistor circuit, what will be the value…

A: The required parameters can be calculated by using the DC analysis of the amplifier circuit.

Q: do 8 IK 31K {2k {k HK 3m4 a) find the current in the 2k resistor b) find the power from the Source

A: The given problem is from circuits. The problem can be solved by using nodal analysis. The…

Q: 6V Μ 502 Μ ΤΩ www 12 Ω www 12 Ω 2V 3Ω 0.11. 1.5 V

Q: 2.16 Determine V, in the circuit of Fig. 2.80. 9V ( Figure 2.80 For Prob. 2.16. 692 www Vo 292 ww +1…

A: The question is about voltage in the circuit.

Q: Given a block diagram for a mechanical system as shown below: R(S) + Gl Find transfer function. T(s)…

Q: H.W 1 Design produce an output given by Vo= 2V₁-5V₂-5 Sv₂d+ an op-Amp circuit that

Q: Write an essay about which types of problems can be solved by using finite state machines.

A: Algorithmic test pattern generating testing for the circuit under test uses finite state machines.…

Q: Y(s) Find the transfer function for the systems represented by the block diagrams below. Do this by…

A: The given block diagram can be reduced by considering the series and parallel connected block…

Q: 1. P = V.I and Unit Review charge, measured in current, measured in voltage, measured in resistance,…

Q: Q3: For a binary communication system, find which input is more probable given that the receiver has…

A: Given the binary communication system, Receiver output= 0 input equally divided to be 0 or 1…

Q: 1. Determine the one-sided spectrum of the signal x(t)=4.0+2.5 cos (400rt+)+1.5 cos (600zt). Give…

Q: Find the Thévenin output resistance of the circuit shown show below. That is, find the resistance…

Q: 3. An input-output relationship of a discrete-system is given by: y[n] = 15x[2n+1] + 8 Say "Yes" or…

A: Given,The input-output relationship of a discrete system is given by,y[n]=15x[2n+1]+8

Q: H. W₂ Vs For the circuit shown below;' Show that ARR (R+R) (R+R)+RR-ARR R Ŕ ww +A ۷۰م

Q: If Van = 220 260° V in the network of the following Figure, find the load phase currents LAB, IBC,…

Q: Vs(t) D2 Vout + DA D3 17 W RL D1

A: Given the circuit, • Diode D3 is damaged so that it is always open circuit regardless of the applied…

Q: 1. A sequential circuit is defined by the following characteristic equations: Q1+ = x’Q1 + xy Q0+…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: 3. A single phase half-wave converter is operated from 230V, 50 Hz source and the load R=1202. For a…

A: Given data Supply voltage, Vrms=230 V Supply Frequency, f=50 Hz Resistance, R=12 Ω Firing angle,…

Q: In detailed steps, describe how to measure a DC voltage with a digital multimeter?

A: Voltage : - Voltage is defined as the potential difference between two terminals is known as…

Q: www.twitt S T

A: Given circuit diagram, R = 50 ohm L = 0.20 H C = 150 μF ω=150 rad/secVm = 30 V Z = ?

Q: Determine i(t) for t >0 in the following circuit if is(t) = 5u(t) A. is 2Ω 8/29 H 1/8 F

A: In this question We need to determine the current in the inductor. We are solving this problem…

Q: 26) If a transistor's beta equals 30 and IB equals 1 mA, IC equals. A) 30 mA B) 1 mA C) 0.33 mA D)…

A: Given, In a transistor, β=30. The base current, IB=1 mA.

Q: Use the residue method to find the starred transform X*(s) of the following functions

A: a) The function Xs is given asXs=s2+5s+6ss+4s+5 ...1By residue method,Xs=As+Bs+4+Cs+5…

Q: A. What is the advantages and disadvantages of using negative feedback? B. Why the bandwidth of the…

A: We need to explain the advantage and disadvantage, we need to explain bandwidth of op amp and slew…

Q: Using the Laplace transform, show that: x(t) ∗ δ(t) = x(t) and x(t) ∗ δ'(t) =

Q: Determine internal bias voltage vont V-=-15 V+=15

A: Op-amp is multistage amplifier. The ideal op-amp have infinite input resistance and infinite gain.…

Q: Find the Z parameter z22 (in Ohms). Let R=0.66 Ohms. (Use 3 decimal places. Unit is not required) R…

Q: Find v (t) for t >0 in the following circuit. i(t) 0.1 H 6u(1) + 10 V - Ug(1) + www 492 4Ω 20₂(1)…

A: The given circuit diagram is shown below. We need to determine vt for t>0.

Q: a /b FE t=0 80 mH 75 75 mA 50 N Ω 40 Ω www 200μF 1. For the circuit shown above, reverse the way in…

Q: Q2. The switch has been closed for a long time. At t = 0, the switch is opened. What is the voltage…

Q: Using Voltage division, find the voltage across the 100 Ohm resistor. V1 U-10 V R1 R=100 Ohm R2…

Q: 2. R1 302 Given the following circuit: V1 -2V (1) Mesh Analysis (2) Nodal Analysis (3) Superposition…

A: Given: The given circuit diagram is, To solve for the current through resistor R1 and the power…

Q: 150 , Z02 50 , and For the transmission line system in Figure 2, and for the values of Z01 1 =…

A: Transmission Line:Z01=150ΩZ02=50Ωl=0.357 λ1To find SWR=?

Q: Problem 4.50 Enhanced with Hints and Feedback Use the mesh-current method to find the branch…

Q: X(t) = A(o (2118L + ( )= AS, (wend) Chittelle Power e Sigand by Integrating One Pensel of the…

A: Given: Xt=Acos2πft+ϕ and Xt=Asinωt+ϕ

Concept explainers

Dielectric Breakdown

A dielectric is a material with low electrical conductivity and so is classified as an insulator. Dielectric materials are used to block the flow of electricity through them, allowing them to behave as an insulators. They can also be used to store electric charge or improve capacitance.Dielectrics have no free electrons for conduction because electrons are tightly bound to the nucleus. Because dielectrics contain a small number of electrons for electrical conductivity, they have a dipole. The two primary roles of dielectrics in electrical devices are insulation and electrical energy storage. An electric field polarizes the dielectric, and the polarization of the molecules allows dielectric materials to store charge.

Question

Need ot very fast i will give multiple upvotes

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
Determine the value of the capacitance, in picofarads, of a parallel-plate capacitor using a dielectric of relative permittivity 4.07 with dielectric thickness 33 mm and plate area 46 cm2. Use 8.854 × 10-12 F/m for the permittivity of free space.
Determine the total capacitance, total charge, individual voltage drop and charges across each capacitor. Use two decimal places for your answer. Put your answer for the individual voltage and charge for each capacitor in a table for faster checking. Thank you! Here are the values for the capacitors: C1 = 34 C6 = 29 C2 = 46 C7 = 38 C3 = 28 C8 = 23 C4 = 43 C9 = 32 C5 = 24 C10 = 23
Between the plates of a capacitor with an area of A = 40 cm², and distance between the plates of d = 30 cm, three dielectric materials are placed, as shown in the following figure. what is the equivalent capacitance of the capacitor with the three dielectric materials with permittivities ε1= 0.20 F / m, ε2=0.30 F / m, ε3= 0.40 F / m ?
A parallel-plate capacitor whose plates have area of 30 cm2 and 5 mm apart contains a medium with relative permittivity 3. What is the capacitance of the capacitor? Lütfen birini seçin: a. 18.75 pF b. 20.34 nF c. 15.93 p F d. 20.34 pF e. 15.93 nF
2. FIND THE EQUIVALENT CAPACITANCE. PLS ANSWER ASAP
Two concentric cylindrical plates have an outer radius of 4 cm, an inner radius of 3.8 cm, and a cylinder length of 10 cm. The gap of both plates contains air. Specify: a. Capacitance of capacitors (in pF, pico-farad). b. Capacitor charge (in nC, nano-coulomb) if the capacitor is connected to a 12 volt power source. c. Capacitance and charge captor if the gap of both plates is filled by the material with a dielectric constant of 2.3.
A capacitor is made from two flat parallel plates placed 2 mm apart, .and its capacitance at vacuum is 10-12- F , if 200 volt applied in between then a Dielectric material was entered and its Dielectric constant Is 49 , Calculate : a) the new value of capacitance after the entrance of the Dielectric b) what is the value of charge on Dielectric material surface c) the polarization p of the Dielectric material d) calculate the displacement and the field inside the Dielectric
A spherical capacitor is formed by the two concentric sphericalconducting shells, separated by a vacuum, and with radii a and brespectively, where b > a. What will be the resulting capacitance in thelimit where b >>a?
A paper dielectric plate capacitor is to be experimentally tested. The metal plates and the paper material between said plates are all 20 cm in radius and subjected to 10V dc in the test. How much is the capacitance does this capacitor have in picofarads (pF), if the paper material between plates used is 2 cm thick? Input answer in 4 decimal places and in pF. Note: Relative permittivity of the paper ( εr ) : 0.4225
Q1 b) Derive the current waveform for a 10μF capacitor if the voltage across the capacitor is as shown in Figure Q1(b). c) The voltage across a 10 F capacitor is v(t) = 5te-2t V. Determine the current that flows into the capacitor and the electrical power of the capacitor. d) Calculate the voltage across each capacitors in Figure Q1(d) during steady state.
Determine the total capacitance, total charge, individual voltage drop and charges across across each capacitor. Use two decimal places for your answer. Please put your answer for the individual voltage and charge for each capacitor in a table for faster checking. Thank you! C1= 27 F C2= 53 F C3= 21 F C4= 50 F C5= 17 F C6= 22 F C7= 45 F C8= 16 F C9= 25 F C10= 16 F V= 110 V Note: This topic is under capacitors.