Question 2: Consider a non-uniform 10m long cantilever beam, with flexural rigidity of 300 kN/m if 0≤x<5 x+15 300 kN/m if 5 ≤ ≤ 10 25-1 a) What are the boundary conditions for this beam? b) Calculate the deflection function for this beam under a uniform distributed load of 10N/m over the whole beam.

Question 2: Consider a non-uniform 10m long cantilever beam, with flexural rigidity of 300 kN/m if 0≤x<5 x+15 300 kN/m if 5 ≤ ≤ 10 25-1 a) What are the boundary conditions for this beam? b) Calculate the deflection function for this beam under a uniform distributed load of 10N/m over the whole beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider a non-uniform 10m long cantilever beam, with flexural rigidity of EI (x) = 300 x + 20 kN m2. a) What is the flexural rigidity at each end of the beam? b) Calculate the deflection function for this beam under a uniform distributed load of 10N/m over the whole beam.
Assume that a max deflection is equal to (length/1000)mm is to be the limiting factor in selecting a W-beam having a span length of 1.35 meters. Fixed at one end and the load at the free end is 20.60kN. I=73,320,591mm^4. Determine the minimum material stiffness( Young's Modulus) in GPa.
assume that a max deflection is equal to(length/1000)mm is to be the limiting factor in selecting a W-beam having a span length of 1.47meters. Supports are at both ends and the load at the center is 24.70kN. I=71,276,243mm^4. Determine the minimum material stiffness(Young's Modulus) inGPa.
A beam with length L is fixed at both ends. It is loaded with a concentrated force P at L/3 from the first support. Draw the loading diagram. If the beam has a length of 10 m, cross section of 200x200mm, and force P is 10 kN, what is the deflection at midspan (in mm)?
The simply supported beam ‘A’ of length L carries a concentrated load P at midspan. Another beam ‘B’ is loaded with a uniformly distributed load such that the total load on the beam is P. Calculate the ratio of maximum deflections between beams A and B. A. 5/8 B. 5/4 C. 4/5 D. 8/5
Question:- 1. What is the flexural rigidity of the beam in N-m^2? 2. What is the value of the maximum vertical deflection in mm? 3. What is the location of the maximum slope of the elastic curve from C in meters?
Calculate the value of the deflection at point B due to concentrated load P in the form ??=??????????? Note: EI will cancel out in further calculations. Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
From figure 07 for questions 7A and 7B, is a cantilever beam with variable moment of inertia, and E = 39000ksi. 7A.) The slope at the free end is approximately equal to. 7B.) The deflection at the free end is approximately equal to.
A simply supported beam with length l is loaded with a uniformly distributed load w. What is the deflection at the distance x = 2.8 m from the left end of the beam in millimeters? l = 6 m w = 20 kN/m EI = 12000 kNm2
The cantilever beam shown has a length of 5m and supporting a uniformly distributed load of 10 kN/m acting 2m from the fixed support at point A to the free end at point C. Determine the deflection at point B. Use E = 200 GPa and I = 15 x 106 mm. Double integration. (Boundary method)
An overhanging beam supports the loads as shown in the figure. If El 3000.65 kNm², determine the value of deflection at point Fin millimeters.
A simply supported steel beam with a moment of inertia of 60 x 106 mm4 of length 7 m has aconcentrated couple Mo of 10 kN-m applied at one end. b) Calculate the value of the maximum deflection.