Question 4 A- Determine cohesive soil density in place, when; Core cutter diameter is 9.8 cm Core cutter height is 12 cm Weight of soil required to fill core cutter is 1.8 kg. B-Why the core cutter suitable for cohesive soil density determination?

Question 4 A- Determine cohesive soil density in place, when; Core cutter diameter is 9.8 cm Core cutter height is 12 cm Weight of soil required to fill core cutter is 1.8 kg. B-Why the core cutter suitable for cohesive soil density determination?

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter4: Plasticity And Structure Of Soil

Section: Chapter Questions

Problem 4.9P

See similar textbooks

Related questions

Q: engineer in-charge decided to under go soil testing. A 480 cubic centimeter (cc) soil sample taken…

A: Given data- Weight of soil (W) = 850.5 g Dry Weight of soil (Wd) = 594.4 g Volume of soil (V)= 480…

Q: The test results of a soil sample are given below. Percentage finer than 4.75 mm = 55 Percentage…

Q: Civil Engineering Q1) a)Describe in detail the Sedimentation test for fine-grained soils…

A: (a) Sedimentation analysis for fine grained soil can be done by either pipette method or by…

Q: Q2 Table 2.A consolidation test data An oedometer test is conducted for a soil sample.The sample is…

Q: 4. Specifications require that a fill using borrow soil to be compacted at 95% of its standard…

A: The optimum moisture content of the soil is the water content corresponding to the maximum dry unit…

Q: A) A sample of the soil was tested in the laboratory and it was found that the clay percent is 10 %…

A: The given data is shown below: Clay=10 %Sand=30 %Silt=60 %

Q: Problem 7: The results of a sieve analysis are reported in Table 3. Plot the gradation curve and…

Q: the given data shows a sieve analysis of a soil sample. classify the soil using aashto method. a.…

A: Given : Liquid limit, LL = 38% Plastic limit, PL = 29% Sieve No. Diameter (in mm) Percentage…

Q: In a shrinkage limit test, the volume and mass of a dry soil pat are found to be 50 cm³ and 88 g…

A: Given data: Volume of soil = 50 cm3 = 50 cc ( 1 cm3 = 1 cc ) Mass of dry soil = 88 g…

Q: FUNDAMENTALS OF GEOTECHNICAL ANALYSIS A constant head permeability test is performed on soil that…

Q: Which of the following nearly gives the %gravel of Soil B using AASHTO? which of the following…

Q: The modified Proctor test (ASTM D 698, method C) was performed for a soil with G, = 2.70, and the…

Q: A proctor compaction test in the laboratory on a borrow pit soil gives maximum unit weight of 19…

Q: From the given table of consistency index and an unconfined compressive strength of the soil.…

Q: The modified Proctor test (ASTM D 698, method C) was performed for a soil with G, = 2.70, and the…

A: Given, Water content (%) Moist weight in mold (gf) 6.5 3250 9.3 3826 12.6 4293 14.9 4362…

Q: Laboratory compaction test results and fielddetermined in-place density (unit weight) results are…

A: The result from the laboratory compaction test and in place field density tests are represented in…

Q: Compaction efficiency is measured by void ratio reduction. Explain the text quantitatively using the…

A: 1.As we know that the void ratio is the ratio of the volume of the voids to the volume of the…

Q: A sample soil for proposed building-the engineer in-charge decided to under go soil testing. A 480…

A: Given data, Volume of soil = 480 cm³ Dry weight of soil = 594.4 gm Total weight of soil = 850.5 gm…

Q: I am working on a lab report for a sieve analysis that was conducted in the lab. I got that the soil…

A: Given data; Percentage of Gravel is 20.5% Percentage of sand is 77.8% Percentage of fines is 1.7%…

Q: 1. From the result of sieve analysis and the grain size curves for soils 1 and 2. a. Compute the…

A: The coefficient of uniformity is defined as the ratio of the size of the soil grain corresponding to…

Q: Which of the following tests aims to know the extent of the soil's ability to be a base layer for…

A: A good base layer for the road must possess the following properties Stability Incompressibility…

Q: Problem 3: A soil sample has a liquid limit of 70 % and plastic limit of 50 %. U-line : PI = 0.9 (LL…

A: Liquid limit:- Liquid limit is the water content where the soil starts to behave as a liquid. Platic…

Q: What is the objective of compacting subgrade in roadworks? Compaction efficiency is measured by void…

Q: A representative soil specimen collected from the a construction site weighs 1,8kN and has a volume…

Q: A new road to be constructed from Sri Gading to Tanjong Laboh is requires field and laboratory…

A: Formula:γwet=WeightVolumeγdry=γwet1+MC

Q: A soil sample was taken from a proposed cut area in a highway construction project and sent to a…

A: given data: In-situ dry unit weight=107.1 lb/ft3Laboratory dry unit weight=112.6 lb/ft3

Q: Select the correct answer(s) to the statement, "disturbed soil samples cannot be used for" Select…

A: KINDLY NOTE that as per our guidelines we are supposed to solve only 1 question. Kindly repost the…

Q: A soil sample has a unit weight of 1.9 g/cc and w=12%. If Gs of solids is 2.65, determine the void…

A: This question is related to Soil Property from soil mechanics. In this question we calculate the…

Q: Calculate the zero-air-void unit weights (kN/m³) for a soil with Gs = 2,68 at moisture contents of…

A: zero air void line - At constant moisture content, the dry unit weight reaches its theoretical…

Q: A soil excavated from a borrow pit has an in place dry unit weight of 18.51 kN/cu.m. In the lab, the…

Q: The soil with Gs = 2.7 and e = 0.8 has been air dried for 6 hours. After %3D %3D drying, the…

A: Given data in question Specific Gravity Void ratio before drying 0.8 Void ratio after drying 0.7…

Q: A 5-lb soil sample was taken from a fill. The volume the hole from which the sample was taken was…

Q: Is it necessary to do stress test of soil in CBR? If so explain in detail about its necessity in…

A: Brief Concept- CBR Test- The California Bearing Ratio Test is a penetration test used to determine…

Q: Table Q2(b)(i) shows the proctor compaction test results of bulk density and percentage of water…

Q: 01-Select the correct answer 1. An undisturbed sample of sand has a dry weight of 19.06 N and a…

Q: Calculate the permeability, K, for Bay mud after solving the following equation (gw is the specific…

A: Data is as given

Q: Given the following SPT result, determine the N-value and the soil’s relative density (No correction…

Q: Statement: Constant head permeability test is a laboratory method for determination of permeability…

A: Answer:- Given statement is false. Constant head permeability test is a laboratory method, but this…

Q: Explain the Tri axial Shear test in your own words.

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A soil specimen has a total volume of 70 cm3 and a total mass of 135.5g. After complete drying in an…

A: V = 70 cm^3 Wet weight W1 = 135.5 g Dry weight W2 = 122 g Gs = 2.60 Void ratio e = ?

Q: highway engineering labartory CBR Test Report Discussion Points 7. What is the reason of…

A: Question is based on CBR test . In the question we have to tell the reason of compacting the soil…

Q: A consolidated-drained test was conducted on a normally consolidated clay. The results are as…

Q: A geosynthetics clay liner (GCL) having a thickness of 10 mm and a permeability of 5X1010 cm/sec.…

A: We are authorized to attempt 3 sub-parts at a time. Since the sub-parts are not mentioned, we are…

Q: Problem 2.1: The following values for a sand are given: D10 = 0.3 mm, D30 = 0.41 mm, and D60 = 0.77…

A: Data given: D10 = 0.3 mm D30 = 0.41 mm D60 = 0.77mm Asked: Uniformity coefficient (CU) based on the…

Q: 2.1 For a gravel with D = 0.48 mm, D30 = 0.25 mm, and D10 = 0.11 mm, calculate the uniformity…

A: (Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: The modified Proctor test (ASTM D 698, method C) was performed for a soil with G, = 2.70, and the…

A: As per company guidelines we are supposed to answer only 3 sub-parts Kindly repost other parts in…

Q: 1. The results of a lab compaction test using standard proctor procedure are shown in Figure 1.…

A: From figure γdmax=117.4lbft3OMC=11.8%

Q: - Organic soils are typically characterized by high void ratio, low specific gravity, and high…

A: void ratio given bye=VVVs=A*HVA*HS=HVHSheight of soild determine byHs=WA*G*γand HV=H-Hsgiven data…

Concept explainers

Pressure and Stress

Question

I need solution in 15 minutese please

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What relationship exists between permeability and void ratio for given soil? Explain.
Please i need help to solve this question.. A sample of the soil was taken for oedometer test and the initial thickness of the sample was 19 mm for astress increment of 100 kPa, calculate coefficient of permeability(k), coefficient of compressibility (mv) andcoefficient of consolidation (cv) from the data obtained as following: (hint: use the root time method). Thank you
Calculate the zero-air-void unit weights (kN/m³) for a soil with Gs = 2,68 at moisture contents of 5, 10, 15, 20, and 25%. Draw a curve y for moisture content....
A single liquid limit test yields a moisture content of 45% for 29 blows. a) Using the one-point method, determine the liquid limit for this soil. List any assumptions that you make. b) What is the Liquid Limit if the moisture content of 45% was achieved for 21 blows? c) Briefly explain why the one-point method provides reasonable results.
Describe the principal modes of soil failure.
Based on AASHTO, the term ____ is applied when the fine fractions of the soil have a plasticity index of 10 or less. Please answer this asap. For upvote. Thanks
ASTM D1556: Standard test method for density and unit weight of soil in place by the sand cone method
Given the following SPT result, determine the N-value and the soil’s relative density (No correction due to the effective overburden pressure is required). Cumulative Depth (in.) Number of Blows 6 5 12 6 18 7 Which of the following is incorrect regarding the Soil Classification Systems?a. The AASHTO Soil Classification System is commonly used in highway design and construction b. In the USCS, SP stands for Poorly Graded Sandc. Both AASHTO and USCS, percent passing #200 sieve is a crucial piece of informationd. Percent passing #4 sieve is required in order to use the AASHTO system
A soil sample has 98% passing the No. 4 sieve and 74% passing the No. 200 sleve. The LL for the soils 58% and the PI is 30%. Classify the soil according to the USCS. Show step by step solutions.
Which of the following nearly gives the %gravel of Soil B using AASHTO? which of the following gives the uniformity coefficient of Soil A? which of the following gives the coefficient of gradation of Soil B?
Consider a soil that is being placed as a fill and compacted using a sheepsfoot roller (a pieceof construction equipment). Will the action of the roller change the void ratio of the soil?Explain.
Briefly describe the phenomenon of liquefaction in soil deposits, indicating type and condition of soil required and occurrences responsible.