Question 5 The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the magnitude of the force P that would result in a 0.18-in. horizontal displacement of bar AB. Use G = 70 x 103 psi for the plastic, and neglect the deformation of the steel frame. 3 ft В Plastic sheet 2 ft

Question 5 The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the magnitude of the force P that would result in a 0.18-in. horizontal displacement of bar AB. Use G = 70 x 103 psi for the plastic, and neglect the deformation of the steel frame. 3 ft В Plastic sheet 2 ft

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=30° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm² and A=50 cm² will be taken for all bars.)
Compute the value of EIy at 2.5 m from the left support.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
Determine support reaction at B . Given P=100 Kn L=10 m
Determine the vertical displacement at Joint A, B, C, D, E
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
Questions b and c. The pressure from part a is 0.86832 Mpa
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
An equilateral triangular plate of side 2.4m placed horizontally in a liquid (sp. gr. 0.80) in such a way that the center of the plate is 2.5m below the free surface of water. (a) Determine the area (in sq. meters) of the plate. (b) Determine the magnitude (in kN) of the resultant force on the plate.
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the ff. A. Vertical reaction at C in kN. B. Moment reaction at C in kN. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.