Question 5. The steel reinforcement of the T-beam is required to be designed to resist the bending moment of 855 kNm. The material properties of the flanged section are concrete cylindrical compressive strength, få is 32 MPa and the characteristic yield strength of the steel reinforcement fa is 460 MPa. b=700 T. ha95 Dimension is in mm b_-420 009

Question 5. The steel reinforcement of the T-beam is required to be designed to resist the bending moment of 855 kNm. The material properties of the flanged section are concrete cylindrical compressive strength, få is 32 MPa and the characteristic yield strength of the steel reinforcement fa is 460 MPa. b=700 T. ha95 Dimension is in mm b_-420 009

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The strain in the x direction at point A on the A-36 structural-steel beam is measured and found to be εx = 217 x 10^6. Determine the applied load P. What is the shear strain γxy at point A?
A hollow circular pole, 6m. thick with 300 mm outside diameter and height of 3 m weighs 150 N/m. The pole is subjected to the following vertical load P= 3KN at an eccentricity e=100mm from the centroid of the section, lateral force H = 0.45 KN at the top of the pole. Note, used combined stresses principle for solving the ff. questions. A. Determine the maximum compressive stress at the base due to the loads. B. If the hollow pole is replaced by a solid wood pole of 250 mm diameter, determine the maximum shear stress. C. Determine the maximum tensile stress at the base due to the loads.
1. Differentiate the permanent and the variable action with suitable examples 2. Analyze the stress-strain relationship of steel. Notes : Internal forces Fcc = 0.567fck(b x 0.8x) = 0.454 fck bx Fst = 0.87 fyk As Moment of resistance with respect to steel, M = Fcc.z Moment of resistance with respect to concrete, M = Fst.z Mbal = Kbal fck bd2 where Kbal = 0.167 As ‘ = (M-Mbal) / 0.87 fyk (d-d’) As = Mbal / 0.87 fyk zbal + As’
A simply supported wood beam with an overhang is subjected to uniformly distributed load q. The beam has a rectangular cross-section with width b = 200 mm and height h = 250 mm. Determine the maximum permissible value q if the allowable bending stress is ?all = 11.2 MPa, and the allowable shear stress is ?all = 1.50 MPa.(Enter the magnitude in kN/m.)
clear cover between the different layers on tension face s 415 grade steel bars are used in the beam thr The beam throughout the span. e A {a) Find out the maximunm bending moment M, at limit state of collapse for the beam s the stress in compression reinforcement a,, = 09566 , corresponding 1o tensile reinforcement at the limit state. (b) What should be the superimposed uniformly distributed load ‘w, the beam can carry & conditions? (¢) Dosign the shear reinforcement at support if design shear strength of concrete
The masonry pier is subjected to the 800kN load. Determine the equation of the line y=f(x) along which the load can be placed without causing a tensile stress in the pier. Neglect the weight of the pier
Answer the following: a) Draw the SFD and BMD of the beam b) max flexural stress in the built-up beam c) max transverse shear stress d) deflection at free end
About Uncracked and Craked Section 1. A doubly reinforced beam has dimension of 300mmw x 600mmh. It is reinforced with 2-25mm diam compression bars and 4 25mm diam tension bars. Concrete cover from centroid of steel bar is 60mm. On its section has a bending moment of 300KN-m. Using working stress design method what are the stresses acting on the concrete, compressive and tensile steel bars? used n: 8
A 350mm x 600mm prestressed beam has a simple span of 20m. Thebeam uses stress relieved tendons with specified tensile strength f pu =1862 MPa and an effective stress in prestressed reinforcement afterallowance for all prestress losses f se = 1100 MPa. The area of prestressreinforcement in tension zone is A ps = 1800mm 2 applied 90mm abovethe bottom of the beam and fc’ = 35 MPa.a. Determine the reinforcement indices for the prestressed beam ifit is not to be grouted (unbonded) after the application of theprestress.b. Determine the reinforcement indices for the prestressed beam ifit uses bonded tendons.c. The safe ultimate moment capacity of the beamd. The safe live load that the prestress beam could carry.
True or false? The strength of under reinforced conc. section is controlled by yield stress of steel (reinforcements).
Mechanics of Deformable bodies The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure stress for the steel is (sfail)st = 350 MPa, determine the minimum thickness t of the pipe if it supports the force of 500 kN. Use a factor of safety against failure of 1.5. Also, find the minimum radius r of the base plate so that the minimum factor of safety against failure of the concrete due to bearing is 2.5. The failure bearing stress for concrete is (sfail)con = 25 MPa
A beam has a diameter of 300 mm with length = 4 m. The engineer decided to replace the circular section with a square section because the circular beam is equal to the strength to the square section having a similar area. a.) Determine the dimensions of the square beamb.)If the allowable shearing stress is 2 Mpa and the allowable bending stress is 16 Mpa, determine the maximum uniform load.