QUESTION 56 Short Problem: Given a series circuit comprised of the following element: 73.24-ohm resistor, practical inductor with internal resistance of 0.78 ohm and reactance of 68.87 ohms; and a capacitor with reactance of 14.82 ohms. Compute for the magnitude of its equivalent impedance in ohms. Note: Follow this reminder carefully. Compute to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer.

QUESTION 56 Short Problem: Given a series circuit comprised of the following element: 73.24-ohm resistor, practical inductor with internal resistance of 0.78 ohm and reactance of 68.87 ohms; and a capacitor with reactance of 14.82 ohms. Compute for the magnitude of its equivalent impedance in ohms. Note: Follow this reminder carefully. Compute to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 16RQ: Explain the difference between cumulative- and differential-compounded connections.

See similar textbooks

Similar questions

34.1. Enumerate five step-by-step procedure of Nodal analysis method in application to ac electric circuit problem solution or analysis.
When an impedance coil is connected to a 114 volt 60 cps source, the current is 3 A. If the current rises to 4 A when a 116 volt 25 cps is is impressed across the coil, determine the values of the resistance and inductance of the coil.
Calculate the value of lx using source tranformation theorem.
Enumerate five step-by-step procedure of Mesh analysis method in application to ac electric circuit problem solution or analysis.
A 15kVA, 440V, single-phase alternator draws a field current of 5A at rated load. With the same field current, the open circuit emf and short-circuit current are 100V and 80A respectively. The ohmic resistance of the armature between terminals is 0.12 ohm. The ratio of effective to ohmic resistance maybe taken as 1.1. Determine the voltage regulation (in %) when the load is purely resistive.
Power System Analysis Please solve the question quickly
Q 03: Briefly discuss, how the energy consumptions for operations of a fork lifter could be justified. Suppose that a fork lifter has a total energy consumption of 150 W.Hr. The total trips of the vehicle are 375. How the battery duty cycle may be calculated in this case?
Given a series circuit comprised of the following element: 68.13-ohm resistor, practical inductor with internal resistance of 0.34 ohm and reactance of 47.15 ohms; and a capacitor with reactance of 7.53 ohms. Compute for the magnitude of its equivalent impedance in ohms. Do not round off during computation. final ans 4 decimal places
Using a neatly and labeled drawn sketch, show the typical circuit arrangement of a monopolar arrangement with ground return
An impedance coil having a resistance of 15 ohms and an inductance of 0.08 henryis connected in series with a variable capacitor. If a 117 volt 60 cps source isconnected to the circuit, what will be the capacitance of the capacitor and the current(a) when the circuit has a power factor of 0.866 leading and (b) when the voltagedrop across the coil is equal to the voltage drop across the capacitor?
The following data were obtained from a short-circuit test performed upon a 50 kVA, 2300/115 V, 60 Hz transformer: Esc = 87 V, Isc = 21.75 A, Psc = 590 W. Calculate (a) equivalent resistance, reactance and impedance referred to the primary, and (b) voltage regulation at a power factor of 0.866 lagging. Subject: Electrical Apparatus and Devices
I want a solution in less than 30 minutes Often, the network is referred as an infinite bus when a change in input mechanical power or in field excitation to the unit does not cause an appreciable change in a. system frequency or terminal voltage b. Total production cost c. system frequency and terminal voltage d. system frequency alone