I need the solution with in 30 minutesThank u a) The minimum radius to the middle of the inner most lane (to the nearest 0.1ft)b) The minimum radius to centerline of the alignment (two 12' lanes in each direction). Question 6:An Alignment is being designed with a 60mph design speed. If a horizontal curve along the alignment has asuperelevation of 6% then solve for:

Answered: Image /qna-images/answer/d42ae328-64e4-4f0e-9094-c35f47b88700.jpg

Answered: Question 6: An Alignment is being…

Question 6: An Alignment is being designed with a 60mph design speed. If a horizontal curve along the alignment has a superelevation of 6% then solve for:

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter15: Geometric Design Of Highway Facilities

Section: Chapter Questions

Problem 8P

See similar textbooks

Related questions

Q: A continuous beam is subjected to a dead load of 10 kN/m and a live load of 25 kN/m. Use NSCP 2001 p...

Q: The 5-day BOD of a wastewater sample is obtained as 190 mg/l (with k = 0.01 h). The ultimate oxygen ...

Q: You are asked to design a horizontal curve for a two-lane road. The road has 3.6- m lanes. Due to ex...

A: We have to design the horizontal curve for a two lane road as per the given data like 3.6 m and maxi...

Q: Solve (D² – 3D+2) y 2e3z +4 sec (eª)

Q: A factory releases a plume into the atmosphere on an overcast summer afternoon. At what distance dow...

A: A plume is a column of liquid, gas, or dust that flows through another. In general, we use the term ...

Q: ow many pounds of concrete (specific weight=24 kN/m3) must a beam of the volume of 0.2 m3 and s.g.=0...

A: Given: concrete specific weight=24 kN/m3, beam volume of 0.2 m3 and s.g.=0.33

Q: Determine the location of the horizontal neutral axis of the section (in mm) with respect to the bot...

Q: Wo

A: A loaded beams have been given and it has been asked to determine shear force, bending moment equati...

Q: A hilltop subdivision takes water from a river 500 ft below it during the night through a pump stora...

Q: A 3m deep sand layer has a specific gravity of 2.68 and a void ratio of 0.60. Under this layer is a ...

A: As the final void ratio is directly given it is not necessary to find compression index to solve set...

Q: A car hits a tree at an estimated 38mph on a 4% downgrade. If skid marks are observed for a distance...

A: Given: Estimated accident velocity = 38mph G = 4% Skid distance on dry pavement = 120 ft , a = 14.5 ...

Q: The absolute maximum Bending Moment in a simply supported beam of span 20 m due to a moving udl of 4...

A: QUE:- The absolute maximum Bending Moment in a simply supported beam of span 20 m due to a moving ud...

Q: Determine which of the truss systems shown in a) to e) are statically determinate, statically indete...

A: Given - Five structures a, b, c , d , e are given in the problem. It is asked to determine whethe...

Q: V3 is 9m/s, find h.

A: ##Calculation of Height h####

Q: What document is required for facilities before they discharge treated wastewater into bodies of wat...

Q: 150 250 125

Q: For the beam and loading shown, determine (a) the equation of the elastic curve, and (b) the deflect...

Q: A door in a tank is in the form of a quadrant of a cylinder of 2 m radius and 2 m wide as shown in f...

A: step 1-

Q: a) Draw a free body diagram of the beam. b) Determine the reactions at the support at point A. 200 3...

Q: 1. For the concrete beam shown, calculate the maximum tensile force (P) that can be applied to the b...

A: Given-

Q: W the shear force and bending moment diagrams. y D/ft 400 ft-lb

A: For Shear Force :- Vx = RA - 80x For section Ab = Ra - 480 For section up to l...

Q: Compute the volume change of a solid copper cube, 40 mm on each edge, when subjected to a pressure o...

A: We have to determine the value of volume change of a solid copper cube 40 mm on each edge when subje...

Q: A 3m deep sand layer has a specific gravity of 2.68 and a void ratiodf 0.60. Under this layer is a 2...

Q: Determine the magnitude and type of bar forces for members BE, CF, DG and FG

A: To find force in member BE,CF,DG,FG

Q: 10.13 A cantilever beam is loaded with force P at its free end to produce a deflection APL/3EI. The ...

A: Solution Stiffness given = Pδ For minimizing the weight for a given stiffness, find the expression...

Q: A door in a tank is in the form of a quadrant of a cylinder of 2 m radius and 2 m wide as shown in f...

Q: A circular culvert 164 ft long extends between two reservoirs as shown. The difference in water surf...

Q: A borehole log profile in a construction project is shown in the figure. The proposed construction w...

A: Given : Net stress, σnet = 12 kN/m3Unit weight of water, γw = 9.81 kN/m3 ...

Q: 25 mm. 8000N 4000N 100 mm D A 4000N

Q: 3. (a) Determine the shear force and bending moment as functions of x. (b) Draw the shear force and ...

Q: Two trains travel on parallel tracks in the same direction. The first train has a length of 100m and...

A: Given data from the problem 200 km/h = 55.55 m/sec 250 km/h = 69.4 m/sec To calculate 1 = t1 2= t...

Q: 6. A C8X11.5 single channel section is bolted to a gusset plate with M22 bolts. Assume A572 Gr.50 st...

Q: What is the effect of rapid set in concrete when transportation is concern? In removing forms, what...

A: 1. Cement is a combination of high-performance Rapid Set Cement and fine sand. It has a quick streng...

Q: The stepped steel shaft carries the torque T. Determine the maximum allowable magnitude of T if the ...

A: We have to determine the value of maximum allowable magnitude of T if the working stress is 12 mpa a...

Q: Wo A

Q: Solve Prob. 9-40 using Castigliano's theorem. 6 kN/m C 3 m 3 m

Q: The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A an...

Q: B D fom {m fm Draw the influence line for the beam 1 Reaction at A 2 Reaction at C 3 Shear at B

Q: the stress produced in rod if tensile load of 3.3 N aplied on circular cross sectional area of 30 mm...

A: This question is related to the Strength of Material.

Q: Determine the diameter of a cast iron pipe which is required to carry water at 10 degrees C at the r...

A: Given Discharge, Q=250 liters/secLoss of head= 2m/100m length of pipeAverage height of pipe wall=0.3...

Q: rectangular raft 3 meters. wide and 6 m. long has a thickness of 60 cm and is constructed of solid t...

Q: ses spaced at 15m apart along both sides of the road. The expected noise by the factory is 125 dB at...

A: solution (A) sound pressure level (SPL) - 1. A sound strain is the tension deviation from environmen...

Q: A falling gradient of 2.5% meets a rising gradient of 3.2% at a reduced level of 235.60 m and a thro...

Q: A cylindrical container filled with a specific liquid has an area of 89 m and a height of 8 meters. ...

A: ##Determination of specific Gravity of the Fluid###

Q: 1. A cylindrical steel tank is manufactured based on the following data: internal pressure: 36 MPa f...

A: Factor of safety=2 Internal pressure=36MPa

Q: a) Draw a free body diagram of the beam. b) Determine the reactions at the supports. c) Replace the ...

Q: You are asked to design a horizontal curve for a two-lane oad. The road has 3.6- m lanes. Due to exp...

Q: An incompressible fluid flows steadily through two pipes of diameter 0.15 m and 0.2 m which combine ...

A: Diameter Of three connected pipes and flow rate of two pipes has been given and it has been asked to...

Q: The roof system of an office building consists of a 150 mm-thick reinforced concrete slab resting on...

Q: A 3m deep sand layer has a specific gravity of 2.68 and a void ratio of 0.60. Under this layer is a ...

Concept explainers

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.

Question

I need the solution with in 30 minutes

Thank u

a) The minimum radius to the middle of the inner most lane (to the nearest 0.1ft)
b) The minimum radius to centerline of the alignment (two 12' lanes in each direction).

Question 6:
An Alignment is being designed with a 60mph design speed. If a horizontal curve along the alignment has a
superelevation of 6% then solve for:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Time and time related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular curve of the highway is designed for traffic moving at 50 mi/hr. If the radius of the curve is 550 ft, what is the correct angle of banking of the road?
A horizontal curve is to be designed for a section of a highway having a design speed of 60 mi/h. (a) If the physical conditions restrict the radius of the curve to 500 ft, what value is required for the superelevation at this curve?(b) Is this a good design?
What is the minimum radius of a horizontal curve required for a highway if the design speed is 55 mph and the superelevation rate is 7%? Use AASHTO tablE
When aligning a highway in a traffic area, it is necessary to provide a horizontal circular curve of radius 295 m , if the design speed is 60 kph , determine the superelevation rate. ( Superelevation to fully counteract centrifugal force use only 75% of the design speed).
A sag vertical curve is to be designed to join a -5% grade to a +2% grade. If the design speed is 65 km/h, determine the minimum length of the curve that will satisfy all criteria. Assume a=3m/squared and perception-reaction time = 2.5 sec.
PROBLEM #1) An existing highway with bearing of N 20deg E to be connected to another highway, with bearing of N 75deg E, by a 4-degree simple curve. What length of curve is required? (SIMPLE AND COMPOUND CURVES) *PLEASE REFER TO THE FORMULAS BELOW*
A highway engineer must stake a symmetrical vertical curve where an entering grade of +0.80% meets an existing grade of - 0.40% at station 10 + 100 which has an elevation of 140.36 m. the length of the curve is known to be 120m. Determine the vertical distance between the highest point and PT and elevation at the highest point.
You are asked to design a horizontal curve for a four-lane road. The road has 12-ft lanes. Due to expensive excavation, it is determined that a maximum of 42 ft can be cleared from the road’s centerline toward the inside lane to provide for stopping sight distance. Also, local guidelines dictate a maximum superelevation of 0.08 ft/ft. What is the highest possible design speed for this curve?
An equal-tangent crest vertical curve is 1000 ft long and connects a +2.5% and a -1.5% grade. If the design speed of the roadway is 75 mi/h, determine the length of curve, does this curve have adequate passing sight distance?
You are asked to design a horizontal curve for a two-lane road. The road has 12 ft lanes. Due to expensive excavation, it is determined that a maximum of 34 ft can be cleared from the roads centerline toward the inside lane to provide to provide for stopping sight distance. Also, local guidelines dictate that a maximum superelevation of 0.08 ft/ft. What is the highest design speed possible for this curve?
Design a Two way - one lane Highway with the following specification. V= 90 kph e=0.05 m=15 m SD=115 m wheel base = 2.25 m C=3 Pavement is rotated at center I =20 Determine the following: Minimum Radius Road Widening Transition Spiral (if any) Vertical Curve Tangent and Length of Curve Road Profile for horizontal alignment with station if the start station is 1+ 000
What is the appropriate super elevation rate for a curve with a 1,200-ft radius on highway with a design speed of 60 mi/h? The maximum design super elevation is 6% for this highway.