Question: In a free-floor flow environment, the base width in the trapezoidal cross-section given in the figure is B=5 m, Manning coefficient n=0.014, slope slope m=1.5, flow rate through the channel Q=40 m3/s flow of flow at h=yo =2 m uniform flow depth What should be the channel base slope lo for Calculate the type of current formed in the channel and the wall shear stress in case of uniform flow. Yo =2 m m 5 т

Question: In a free-floor flow environment, the base width in the trapezoidal cross-section given in the figure is B=5 m, Manning coefficient n=0.014, slope slope m=1.5, flow rate through the channel Q=40 m3/s flow of flow at h=yo =2 m uniform flow depth What should be the channel base slope lo for Calculate the type of current formed in the channel and the wall shear stress in case of uniform flow. Yo =2 m m 5 т

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows in a trapezoidal channel at a depth of 40cm and with a velocity of 10m/s. An obstruction causes a hydraulic jump to be formed. What is the depth of flow downstream of the jump? The bottom width of the channel is 5m, and the side slopes are 1 vertical to 1 horizontal.
Water flows uniformly in a rectangular concrete open channel that is 10 m wide at a depth of 3m. The channel slope is 0.0025. Using n = 0.013. Find the velocity, flow rate and the boundary shear stress.
Design a straight trapezoidal erodible channel that can carry a discharge of 12.5m^3/s using tractive force method based on the following information. The side slope is 1V:4H The bottom slope is 0.0015 The manning's roughness coefficient is 0.024 The critical shear stress as 7.2KN/m^2 Angle of repose is 23 Density of water 1000kg/m^3
An unsymmetrical trapezoidal channel with one side inclined from horizontal by 35 degree and the other inclined from vertical by 40degree is to be designed to carry a 2.0 cubic meters per second discharge. Determine the dimensions of the channel for most efficient section if roughness coefficient is 0.030 and average longitudinal slope is 0.05. Draw the cross section of the open channel considering the freeboard height. Use Chezy and Kutter’s C formula.
A trapezoidal channel with sidewalls of 60 degrees has a bottom width of 4 m at total depth of 5 m and has a constant bedslope of 0.005. A flow of 40 m3/s fills the channel to a depth of 3.5 m, the maximum for normal operation. Downstream a topographic constriction requires that the channel be rectangular with a maximum width of 4 m. Assuming no changes in materials and no energy losses, estimate the depth in the downstream rectangular section and recommend a total depth for the rectangular channel.
Determine the hydraulic depth D (average depth) of a triangular channel with right angle corner (900) with a depth of 3 meters.
Q4) A rectangular open channel of width 3.0 m carries a discharge of 2.5 m3/s at an average velocity of 0.6 m/s. Determine the maximum possible constriction in width without affecting the upstream depth, assuming friction losses through the constriction are negligible. If the constriction is associated with a smooth upwards step in the bed of 0.2 m, determine the minimum channel width for the same upstream condition.
The rectangular channel below tapers gradually from 10 ft wide to 6 ft wide, with a transition as shown. If water flows with a velocity of 3 ft/s on the 10-ft-wide side, determine the depth y2 on the 6-ft-wide side. Also, what is the horizontal force directed downstream that the water exerts on each of the flared wing walls?
A trapezoidal channel of bed width 10.0 m and 2:1 side slopes. Determine the Froude number if the specific energy is 2.5 m and the discharge is 25 m3/sec.
A rectangular channel 6.1 m wide with n = 0.014 is laid on a slope of 0.001 and terminates in a free overfall. Upstream 300 m from the overfall is a sluice gate that produces a depth of 0.47 m immediately downstream. (a) For a discharge of 17.0 m3 /s, draw the NDL. CDL and the water surface profile that occurs in the channel. Do you expect a hydraulic jump to occur in the channel? (b) From the overfall up to a location where the depth is 1.2 m, compute and plot the water surface profile using the direct step method. please solve it in a simple way
An unsymmetrical trapezoidal channel with one side inclined from vertical by 35o and the other inclined from horizontal by 40o is to be designed to carry a 2.5 cubic meters per second discharge. Determine the dimensions of the channel for most efficient section if roughness coefficient is 0.025 and average longitudinal slope is 0.05. Draw the cross section of the open channel considering the freeboard height. Use Chezy and Kutter’s C formula.
The trapezoidal channel is to carry 18 m^3/s of flowrate with a bottom slope of 0.0009. Given that Manning’s n is 0.026 and the sides of channel are inclined 63.4° to the vertical, determine the bottom width, depth and velocity for the best hydraulic section.