QUESTION The figure shows an idealized two-cell symmetric wing box structure. Dimensions of the box are 12 in x5 in. All boom areas and panel thicknesses are given on the figure. If all pan the wing box are made of the same material, and the following loads are applied: A vertical Sy = 1,500 Ib along the middle vertical web, and a torque T= 750 lb.in (clockwise). Cal the maximum shear flow in the wing box. %3D Solution: I in.? 0.3" 0.5 in.2 0.3" O. 0.5" 0.5"

QUESTION The figure shows an idealized two-cell symmetric wing box structure. Dimensions of the box are 12 in x5 in. All boom areas and panel thicknesses are given on the figure. If all pan the wing box are made of the same material, and the following loads are applied: A vertical Sy = 1,500 Ib along the middle vertical web, and a torque T= 750 lb.in (clockwise). Cal the maximum shear flow in the wing box. %3D Solution: I in.? 0.3" 0.5 in.2 0.3" O. 0.5" 0.5"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pulley with diameter D = 27 in weighs 80 lb. It is mounted on the diameter d = 2-in axle. A weight of 1000 lb is to be lifted. If the coefficient of friction f = 0.1, what vertical pull force P will be needed?
A block with weight W (W=75 lbs) can move vertically between two smooth walls. It is held by a rope which passes around three fixed rough pegs (coefficient of static friction u=0.25) as shown in the figure. Calculate the force F which will ensure that the block remains suspended.
A 15 kg box rests on a horizontal surface attached to a 5 kg box as shown below. Determine the acceleration of the system and the tension of the rope. μs = 0.4 μk = 0.35
Determine support reaction. P=800 lb , a=5 ft b=9 ft
There is a cylinder X weighing 735.75 Newtons that is held against a smooth incline and is being supported by a weightelss rod Y at 20°. Calculate all the forces that is acting on cylinder X. Solve using equilibrium of concurrent force system. Draw fbd please thank you.
A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area. The correct answer is 2.84. Show solution.
A vertical rectangular gate weighs 6000 lbs and is 10 ft tall and 8 ft wide (into the paper). The gate slides in vertical slots in the side of a reservoir containing water. The coefficient of friction between the slots and the gate is 0.03. Determine the minimum vertical force required to lift the gate when the water level is 4 ft above the top edge of the gate. [Answer in units of lbs.]
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
Please solve the unknown forces using Three Moment Equation. Thank you. Wu = 23.2 kN/m L1 = 5m L2 = 6m
Determine the force in each member of the crane shown in figure below. 5200lb
Calculate the vertical reaction at support A. Enter your answer in kN to two decimal places.
(c) Figure Q2(c) shows a homogenous 1.2 m wide and 3 m long rectangular gate is held in place by a horizontal flexible cable. Water acts against the gate, which is hinged at point A. Calculate the magnitude, FR and location of the resultant force, yR.