QUESTIONS: 1. What is the Transfer function? 2. What do the BODE diagram and poles-zeros graph tell us? What is their main purpose? 3. Write the transfer function of figure 1.3 for the given values, add the BODE diagram and poles-zeros graph. 4. Take the K1=1 N/m, K2=2 N/m, fv=1 N-s/m, M1=M2=2 kg, and find the transfer function of figure 2.1. 5. Implement the transfer function of figure 2.1 to Matlab and plot the BODE and poles-zeros graph. 2

QUESTIONS: 1. What is the Transfer function? 2. What do the BODE diagram and poles-zeros graph tell us? What is their main purpose? 3. Write the transfer function of figure 1.3 for the given values, add the BODE diagram and poles-zeros graph. 4. Take the K1=1 N/m, K2=2 N/m, fv=1 N-s/m, M1=M2=2 kg, and find the transfer function of figure 2.1. 5. Implement the transfer function of figure 2.1 to Matlab and plot the BODE and poles-zeros graph. 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Create a bode plot without using software for the transfer function below.
Tuned Circuit Design Using a VARICAP (a) Refer to the capacitance curves for the Motorola 1N4002 The input tuning circuit of a standard analog FM radio is given below. Specify, that is design for, a voltage, capacitance, and inductance required to tune the circuit to the center frequency of KUMD-FM which operates at 103.3 MHz. Sketching and labeling a representative resonance curve is required to support your calculations. There is no single correct design answer set of values since it depends upon the voltage you initially select to tune your diode.
2. Prove that , for a radio receiverOutput SNR in dB = Input SNR (dB) - Noise Figure(NF)[You can start the derivation from the relation connecting Noise Figure (NF)and Noise Ratio(F) ] note: the answe will be by hand written.
The Bode plot of a transfer function H is shown in Figure 1. What is H in its standard form? In your estimate, what is the magnitude of the transfer function H at as shown in Figure 1? Answer should be given in its original value not the dB value. Note that HdB = 20 log H, where H is the original value.
What is a Bode plot?
1. Why must the algebraic sum of the quadrature components in a parallel circuit be zero at resonance? 2. For the given values of L and C when will a two-branch parallel circuit be in resonance at the same frequency as a series R-L-C circuit?
(can you solve it fast?) Which ones are correct about Nyquist's Theorem in sampling? I. Relates the conditions on the time and frequency planes ii. Helps quantize iii. They determine the bandwidth requirement iv. Returns the spectrum of the sign
The bode plot of the open loop transfer function of a quadratic system is shown above. If the settling time of the closed loop system is 4 seconds, calculate the undamped natural frequency of the system, the damping ratio, the highest amplitude value of the frequency response of the closed loop system and at which input frequency it occurs. Attention!!!: Use the numbers as three decimals during the design phases. Solution: Belonging to the closed-loop transfer function Damping rate = [ ? ] Undamped natural frequency = [ ? ] rad/s The highest amplitude value of the frequency response [ ? ] and [ ? ] occurs at the rad/sec input frequency.
Find the Bode plot of the magnitude of the transfer function given below. Sketch the asymptotic plots for all the factors..explain if possible
referring to the attached equation, 1.Determine the breakpoints of the above function. 2.Choose the magnitude, phase angles and asymptotes of eachbreakpoint. 3.Sketch the bode plots of the transfer function. Indicate on your plot allthe corner frequencies, slopes of sloping line, gains of sloping linesand gain, and phase levels on zero slope lines.
please Calculate the gain margin, phase margin and magnitude of bode plot for the transfer function
For the closed loop transfer function what are they comparing with and how did they draw the bode plot?