QUIZ – BENDING STRESS The beam is made from three boards nailed together as shown. If the moment acting on the cross section is M = 600 N.m, (a) determine the maximum bending stress in the beam. (b) Sketch the stress distribution acting over the cross section. 25 mm 150 mm 20 mm 200 mm M = 600 N.m 20 mm

QUIZ – BENDING STRESS The beam is made from three boards nailed together as shown. If the moment acting on the cross section is M = 600 N.m, (a) determine the maximum bending stress in the beam. (b) Sketch the stress distribution acting over the cross section. 25 mm 150 mm 20 mm 200 mm M = 600 N.m 20 mm

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.12P: Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft....

See similar textbooks

Similar questions

From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
Topic: Strema A 750-mm high cylinder carries a load P which produces a normal stress at its cross-sectional area and a shear stress at its lateral surface area. Find its diameter if these stresses are equal. Choices: A. 3.0 m B. 4.5 m C. 1.5 m D. 6.0 m
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 2 m depth. a. 17.8 b.393.9 c.63.0 d.3.9
n figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide.(a) if the allowable stresses 200 MPa for bearing in the plate material and 120MPa for shearing of the rivet, determine the minimum thickness of each plate.(b)Under the conditions specified in part (a) what is the largest average stress in the plate. Answer a and b please
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding.
A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
Determine the outside diameter of a hollow steel rod that will carry atensile load of 55,000 kg at a stress of 1,500 kg/cm2 and the wallthickness is 10 mm.A. 8.17 cm C. 12.67 cmB. 8.34 cm D. 7.28 cm
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 2. Assume P = 80 kN and Q = 140 kN.
For the beam shown below, b = 5 in and h = 12 in. If the beam is subjected to a transverse shear for of V = 8 kip, determine the largest shearing stress in the beam. Express your answer in psi to the nearest whole psi
A bearing pad is a device which is used to support a bridge or other heavystructure in a way that permits the load to shift slightly in a horizontal directionrelative to the ground or foundation. If a horizontal force af 528 kN is applied tothe top surface of the bearing pad, and that a = 700 mm, b = 550 mm, h = 75m and the modulus of elasticity G = 1.25 MPa. Determine the following: a. The average shear stress on the bearing pad.b. The horizontal displacemant of tne bearing pad. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.
Consider a wood beam (see figure) carrying a uniform load of 16.5 kN/m (which includes the weight of the beam). The length is 1.55 m and the cross section is rectangular with width 150 mm and height 300 mm. * Inserted Photo* If the beam is simply supported as in figure part (a), calculate the maximum shear stress ?max and the maximum bending stress ?max. (Enter the magnitudes in MPa.) ?max= ? MPa ?max= ? MPa (b) If the beam has a sliding support at right as in the figure part (b), calculate the maximum shear stress ?max and the maximum bending stress ?max. (Enter the magnitudes in MPa.) ?max= ?MPa ?max= ? MPa
1. Consider Figure FE 1. In reference to the figure, prepare a concise explanation of the relationship between the vertical stress increments due to surface loads and the parameters that affect it. Focus on the distances from the bearing areas/point to the any point of interest